The article presents the results of research on the ion nitriding process of the so-called difficult to nitride 316L austenitic steel. The main aim of these studies was to determine what influences the intensification of the nitriding process as a result of using an active screen. Two variants of placing the nitrided elements in the glow discharge chamber were adopted: directly on the cathode and on the cathode using an active screen. After the nitriding processes were carried out, the influence of the adopted process parameters on the depth of nitrogen diffusion into the nitrided substrate was analyzed. In the further part of the work, an ionizing nitriding mechanism with the active screen method was proposed, explaining the significant increase in the effectiveness of the nitriding process using the active screen.

The article presents the results of the research on the nitriding process of 316L austenitic steel and the change in surface properties resulting from this process used in medicine, orthopedics, and in fuel cells. The processes were carried out with the following parameters: time from 5 to 17 h, temperature from 430 °C to 490 °C. The study presents the results of tests of the 316L austenitic steel substrate layer subjected to plasma nitriding of a direct current glow discharge, i.e., in the area isolated from both the cathode and the anode. Additionally, the influence of the active screen on the nitriding process in this area of the direct current discharge was studied. The following tests were carried out: nitrogen diffusion depth test, hardness test, wear resistance test, microstructure analysis, corrosion resistance, and distribution of the element concentration in the surface layer. The research allowed for the conclusion that each variant of nitriding contributed to a change in the examined properties, while the observed scale and nature of the changes were different.

Competencies of employees and competence management are elements fairly well described in the literature. A modern approach to these issues, however, must have a broader than traditional character. This follows the significant changes that took place in management sciences expressed by an increased role of intangible assets. Intellectual capital, its components, connections with enterprise resources and elements of the environment are an important aspects of the strategic considerations undertaken by management staff in modern enterprises. Competences - which are specific expression of the potential of employees, their ability to detect changes and finding solutions - in this new context become even more important. This study attempts to analyze the selected relationships between the competency management system, intellectual capital and the attitude to IC of management staff.

The study assessed the effect of ion nitriding on the properties of the surface layer of Grade 5 titanium alloy used, among others, in medicine. Titanium and its alloys have low hardness and insufficient wear resistance in conditions of friction which limits the use of these materials. The improvement of these properties is only possible by the appropriate modification of the surface layer of these alloys. The ion nitriding process was carried out in a wide temperature range, i.e., 530–590 °C, and in the time range 5–17 h. Two variants of nitriding were applied: cathodic (conventional) nitriding and nitriding using the active screen method. The research results presented in this article allow for stating that each of the applied nitriding variants improves the analysed properties (nitrogen diffusion depth, hardness, wear resistance, microstructure analysis and surface topography) of the surface layers in relation to the material before nitriding. The hardness increased in every nitriding variant (the use of the additional active screen increased the hardness to 1021 HK0.025). The greatest increase in titanium abrasion resistance was found for surfaces after cathodic nitriding with an active screen. Each of the applied nitriding variants resulted in surface development.

This paper presents a comparison of two-component ammonia-based inlet atmospheres diluted with either hydrogen (NH₃/H₂) or nitrogen (NH₃/N₂). Taking advantage of the features of inlet atmospheres diluted with nitrogen and hydrogen, four two-stage processes were designed and carried out, which were juxtaposed with two single-stage processes carried out only in an NH₃ atmosphere. A common parameter of the processes carried out was the same value of nitrogen availability in each process stage. The gas nitriding process was carried out on ASIS 1085 non-alloy steel and ASIS 52100 alloy steel. It was found that the chemical composition of the steels studied, for the adopted nitriding process parameters, did not affect the kinetics of the growth in the mass of nitrided samples as a function of the nitriding time. However, the additions of alloying elements present in the steels studied significantly affected the nitrogen distribution between the resulting iron nitride layer and the diffusion zone in the nitrided substrate. Because of the presence of chromium in AISI 52100 steel, a larger mass of nitrogen accumulated in the nitriding zone in the solution compared with unalloyed AISI 1085 steel. As a result, with the same increase in the mass of nitrided steel, a thicker layer of iron nitrides formed on AISI 1085 steel than on AISI 52100 steel.

Sustainable development is an opportunity for modern enterprises to build unique market advantages, but it is always a kind of compromise between financial benefits and activities focused on environmental protection. It also requires companies to be able to acquire and process information, the sources of which are both internal and external, and to process it into effective knowledge. Quality management processes are an important element supporting knowledge management as a consequence of similar priorities. There are direct and indirect relationships between quality management, knowledge management and sustainable development. Related issues are an important element of modern research, but there are still some knowledge gaps that need to be filled. The authors, based on the literature analysis, concluded that there are no studies defining the relationship between quality management and knowledge management in the context of sustainable development relating to the Polish metal industry. Therefore, the objective of this study is to identify patterns of company activities in the area of knowledge management relating to the improvement of manufacturing processes in companies operating in the metal industry in Poland. At the same time, it was indicated which aspects of knowledge management are at the centre of management’s concerns. The study was carried out using a survey questionnaire, with 1930 questionnaires collected from employees in 50 companies selected for the study. The study carried out discovered that in the various areas of the Japanese knowledge management model, companies distribute the emphasis differently, which manifests itself in the procedures and ways of operating. At the same time, there are significant differences between large and medium-sized enterprises, indicating that the scale of operation influences the perception of the importance of individual elements of the knowledge management system in the context of sustainable development.