LIPING GUO

Dr. LIPING GUO

Department of Engineering Technology, Northern Illinois University, DeKalb, IL 60115, USA
orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 March 2009 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
LGLIPING GUO
LIPING GUO
JHJohn Y. Hung
John Y. Hung
RNR. M. Nelms
R. M. Nelms
In this paper, digital proportional-integral-derivative (PID)-type and fuzzy-type controllers are compared for application to the buck and boost dc-dc converters. Comparison between the two controllers is made with regard to design methodology, implementation issues, and experimentally measured performance. Design of fuzzy controllers is based on heuristic knowledge of converter behavior, and tuning requires some expertise to minimize unproductive trial and error. The design of PID control is based on the frequency response of the dc-dc converter. Implementation of linear controllers on a digital signal processor is straightforward, but realization of fuzzy controllers increases computational burden and memory requirements. For the boost converter, the performance of the fuzzy controller was superior in some respects to that of the PID controllers. The fuzzy controller was able to achieve faster transient response in most tests, had a more stable steady-state response, and was more robust under some operating conditions. In the case of the buck converter, the fuzzy controller and PID controller yielded comparable performances.

8 June 2012 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
SOSaid Oucheriah
Said Oucheriah
LGLIPING GUO
LIPING GUO
In this paper, a robust adaptive sliding-mode controller is designed for a boost converter with an unknown resistive load and external input voltage. Adaptation laws are designed using state observers. The closed-loop system for the boost converter is shown to be asymptotically stable. Finally, the robustness of the adaptive controller to input voltage and load uncertainties and variations is tested experimentally.

1 January 2011 in Electric Power Systems Research
Verified
Journal Article
Closed access
LGLIPING GUO
LIPING GUO
JHJohn Y. Hung
John Y. Hung
RNR.M. Nelms
R.M. Nelms

1 February 2011 in Energy Conversion and Management
Verified
Journal Article
Closed access
LGLIPING GUO
LIPING GUO
KYKarthik Yedavalli
Karthik Yedavalli
DZDonald Zinger
Donald Zinger

1 December 2016 in The Electricity Journal
Verified
Journal Article
Closed access
XLXiaonan Lu
Xiaonan Lu
JWJianhui Wang
Jianhui Wang
LGLIPING GUO
LIPING GUO

8 June 2022 in IEEE Access
Verified
Journal Article
Open access
LGLIPING GUO
LIPING GUO
NANauman Moiz Mohammed Abdul
Nauman Moiz Mohammed Abdul
MVMadhav Vengalil
Madhav Vengalil
KWKezhou Wang
Kezhou Wang
ASAlecia Santuzzi
Alecia Santuzzi
Microgrids are the main building blocks of future smart grids. They provide a promising solution for integrating renewable energy sources and distributed power generation into the power grids. The high penetration of renewable energy sources and their intermittent nature have brought about significant challenges to the control and operation of microgrids. In recent years, an enormous amount of research has been conducted on microgrid dynamics, stability analysis, power management, and control. However, there has been limited effort to integrate cutting-edge technologies into classrooms and laboratories. Many academic institutions face special challenges in establishing microgrid laboratories because of the rapid development of technology, cost, and space requirements, as well as daily and seasonal variations in renewable energy sources. Virtual and remote laboratories have become widely accepted for conducting experiments in higher education. A virtual laboratory is particularly suitable for renewable energy-based microgrids to overcome cost, space, and time restrictions. In this study, a web-based virtual laboratory for microgrids with renewable energy sources was designed and used for renewable energy education. The virtual laboratory was developed using NI® LabVIEW, Microsoft®.Net Core, and MATLAB/Simulink®. Innovative courseware was developed around the virtual laboratory and used in several engineering technology courses to teach topics including solar and wind power, data acquisition, DC-DC converters, battery management, and microgrids. The evaluation showed that the virtual laboratory greatly increased students’ awareness, interest, and knowledge of renewable energy. It provides an interactive and convenient tool to engage students to experiment with renewable energy and microgrids.