Bamboo is a rapid renewable plant that has a fast growth rate as compared to trees, which increases its suitability to be used as a sustainable source for wood industry, especially in construction works. Due to the lack of understanding on bamboo properties, the utilization of bamboo in construction has always been neglected. This paper presents an investigation on the mechanical properties of four species of treated bamboos that are available in Malaysia, which include Bambusa Vulgaris, Dendrocalamus Asper, Schizostachyum Grande, and Gigantochloa Scortechinii. A mechanical testing was carried out in various parts along the culm of these bamboo species in order to examine the differences of their compressive strength and tensile strength. The strength development and moisture content of these bamboo species were also monitored at a five-month interval. The results showed that Bambusa Vulgaris, Dendrocalamus Asper, and Gigantochloa Scortechinii possess excellent mechanical properties in compression and tensile strength, which indicate a good quality to be used as a construction material. As bamboo offers promising advantages, thus, it is suitable to be used as a substitute in place of structural timber in construction, which indirectly facilitates the preservation of the global environment.
This paper presents the experimental results on the behavior of fly ash geopolymer concrete incorporating bamboo ash on the desired temperature (200 °C to 800 °C). Different amounts of bamboo ash were investigated and fly ash geopolymer concrete was considered as the control sample. The geopolymer was synthesized with sodium hydroxide and sodium silicate solutions. Ultrasonic pulse velocity, weight loss, and residual compressive strength were determined, and all samples were tested with two different cooling approaches i.e., an air-cooling (AC) and water-cooling (WC) regime. Results from these tests show that with the addition of 5% bamboo ash in fly ash, geopolymer exhibited a 5 MPa (53%) and 5.65 MPa (66%) improvement in residual strength, as well as 940 m/s (76%) and 727 m/s (53%) greater ultrasonic pulse velocity in AC and WC, respectively, at 800 °C when compared with control samples. Thus, bamboo ash can be one of the alternatives to geopolymer concrete when it faces exposure to high temperatures.
This present study evaluates the effect of silica modulus (Ms) and curing temperature on strengths and the microstructures of binary blended alkali-activated volcanic ash and limestone powder mortar. Mortar samples were prepared using mass ratio of combined Na2SiO3(aq)/10 M NaOH(aq) of 0.5 to 1.5 at an interval of 0.25, corresponding to Ms of 0.52, 0.72, 0.89, 1.05 and 1.18, respectively, and sole 10 M NaOH(aq). Samples were then subjected to ambient room temperature, and the oven-cured temperature was maintained from 45 to 90 °C at an interval of 15 °C for 24 h. The maximum achievable 28-day strength was 27 MPa at Ms value of 0.89 cured at 75 °C. Samples synthesised with the sole 10 M NaOH(aq) activator resulted in a binder with a low 28-day compressive strength (15 MPa) compared to combined usage of Na2SiO3(aq)/10 M NaOH(aq) activators. Results further revealed that curing at low temperatures (25 °C to 45 °C) does not favour strength development, whereas higher curing temperature positively enhanced strength development. More than 70% of the 28-day compressive strength could be achieved within 12 h of curing with the usage of combined Na2SiO3(aq)/10 M NaOH(aq). XRD, FTIR and SEM + EDX characterisations revealed that activation with combined Na2SiO3(aq)/10 M NaOH(aq) leads to the formation of anorthite (CaAl2Si2O8), gehlenite (CaO.Al2O3.SiO2) and albite (NaAlSi3O8) that improve the amorphosity, homogeneity and microstructural density of the binder compared to that of samples synthesised with sole 10 M NaOH(aq).
The development of sustainable, environmentally friendly alkali-activated binder has emerged as an alternative to ordinary Portland cement. The engineering and durability properties of alkali-activated binder using various precursor combinations have been investigated; however, no study has focused on the impact of high-volume natural pozzolan (NP) on the acid resistance of alkali-activated NP and limestone powder. Therefore, the current study assesses the impact of high-volume natural pozzolan (volcanic ash) on the durability properties of alkali-activated natural pozzolan (NP) and limestone powder (LSP) mortar by immersion in 6% H2SO4 for 365 days. The samples were prepared with different binder ratios using alkaline activators (10 M NaOH(aq) and Na2SO4) combined in a 1:1 ratio and cured at 75 °C. NP was combined with the LSP at three different combinations: NP:LSP = 40:60 (AAN40L60), 50:50 (AAN50L50), and 60:40 (AAN60L40), representing low-volume, balanced, and high-volume binder combinations. Water absorption, weight change, and compressive strength were examined. The microstructural changes were also investigated using FTIR, XRD, and SEM/EDS characterization tools. Visual examination showed insignificant deterioration in the sample with excess natural pozzolan (AAN60L40) after 1 year of acid exposure, and the maximum residual strengths were 20.8 MPa and 6.68 MPa in AAN60L40 and AAN40L60 with mass gain (1.37%) and loss (10.64%), respectively. The high sulfuric acid resistance of AAN60L40 mortar was attributed to the high Ca/Si = 10 within the C-A-S-H and N-A-S-H formed. The low residual strength recorded in AAN40L60 was a result of gypsum formation from an acid attack of calcium-dominated limestone powder. The controlling factor for the resistance of the binder to acid corrosion was the NP/LSP ratio, whose factor below 0.6 caused significant debilitating effects.
As the fastest growing plant with high tensile strength, bamboo provides an excellent alternative material to replace steel reinforcement in a concrete structure. However, the bond of bamboo embedded in concrete is very poor due to its surface properties and swell–shrink behaviors, especially when embedded in ordinary Portland cement concrete (OPCC). Thus, this paper presents the experimental investigation on the bond performance of deformed and undeformed bamboo species of Bambusa vulgaris strips embedded in fly ash geopolymer concrete (FAGC). Undeformed bamboo strips with and without nodes were compared to deformed bamboo strips in a corrugated and Galvanized Iron (G.I) rolled wired form in the pull-out test to study the mechanical interlocking effect on the bond performance of bamboo strips embedded in concrete. The groove on the corrugated bamboo strip was made using a router machine, while the wired bamboo was produced by wrapping the G.I wire along the bamboo strip. The difference in groove and wire spacing of the deformed bamboo strip on the bond strength was also observed. The result showed that the geometry of the bamboo strip had a significant effect on the bond performance, with the deformed bamboo strip outperforming the undeformed bamboo strip. In addition, the utilization of FAGC could also reduce the moisture absorption by the bamboo strip. Thus, these results showed that using bamboo strips in FAGC is feasible, contributing to a promising approach for full utilization of bamboo and industrial waste products such as fly ash as construction materials.