Seung-Chang Han

Dr. Seung-Chang Han

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 February 2023 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
UCUmer Masood Chaudry
Umer Masood Chaudry
SHSeung-Chang Han
Seung-Chang Han
Tea-Sung JunTea-Sung Jun
Tea-Sung Jun

1 March 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
HKHyun-Hak Kang
Hyun-Hak Kang
SHSeung-Chang Han
Seung-Chang Han
MJMin-Ki Ji
Min-Ki Ji
JLJeong-Rim Lee
Jeong-Rim Lee
Tea-Sung JunTea-Sung Jun
Tea-Sung Jun

21 May 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
SSSumaira Sadiq
Sumaira Sadiq
HTHafiz Muhammad Rehan Tariq
Hafiz Muhammad Rehan Tariq
SHSeung-Chang Han
Seung-Chang Han
NNNur Izzati Muhammad Nadzri
Nur Izzati Muhammad Nadzri
Tea-Sung JunTea-Sung Jun
Tea-Sung Jun

10 July 2021 in Metals
Verified
Journal Article
Open access
PDF file
UCUmer Masood Chaudry
Umer Masood Chaudry
SHSeung-Chang Han
Seung-Chang Han
FAFathia Alkelae
Fathia Alkelae
Tea-Sung JunTea-Sung Jun
Tea-Sung Jun
In the present study, the effect of post-weld heat treatment (PWHT) on the microstructure and mechanical properties of friction stir welded (FSW) DP780 steel sheets was investigated. FSW was carried out at a constant tool rotation speed of 400 rpm and different welding speeds (200 mm/min and 400 min/min). A defect free weld was witnessed for both of the welding conditions. The mutual effect of severe plastic deformation and frictional heat generation by pin rotation during the FSW process resulted in grain refinement due to dynamic recrystallization in the stir zone (SZ) and thermo-mechanically affected zone (TMAZ). Lower tensile elongation and higher yield and ultimate tensile strengths were recorded for welded-samples as compared to the base material (BM) DP780 steel. The joints were subsequently annealed at various temperatures at 450–650 °C for 1 h. At higher annealing temperature, the work hardening rate of joints gradually decreased and subsequently failed in the softened heat-affected zone (HAZ) during the uniaxial tensile test. Reduction in yield strength and tensile strength was found in all PWHT conditions, though improvement in elongation was achieved by annealing at 550 °C. The digital image correlation analysis showed that an inhomogeneous strain distribution occurred in the FSWed samples, and the strain was particularly highly localized in the advancing side of interface zone. The nanoindentation measurements covering the FSWed joint were consistent with an increase of the annealing temperature. The various grains size in the BM, TMAZ, and SZ is the main factor monitoring the hardness distribution in these zones and the observed discrepancies in mechanical properties.

14 May 2025 in Scripta Materialia
Verified
Journal Article
Open access
YIYuki Ikeda
Yuki Ikeda
SHSeung-Chang Han
Seung-Chang Han
TWTheophilus Wallis
Theophilus Wallis
RKReza Darvishi Kamachali
Reza Darvishi Kamachali
RMRobert Maaß
Robert Maaß

16 September 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
UCUmer Masood Chaudry
Umer Masood Chaudry
SHSeung-Chang Han
Seung-Chang Han
KTKaab bin Tayyab
Kaab bin Tayyab
AFAmeeq Farooq
Ameeq Farooq
WKWoo-Sung Kim
Woo-Sung Kim
Tea-Sung JunTea-Sung Jun
Tea-Sung Jun