The fault-slip type of rock burst is a major threat to the safety of coal mining, and effectively recognizing its signals patterns is the foundation for the early warning and prevention. At first, a mechanical model of the fault-slip was established and the mechanism of the rock burst induced by the fault-slip was revealed. Then, the patterns of the electromagnetic radiation, acoustic emission (AE), and microseismic signals in the fault-slip type of rock burst were proposed, in that before the rock burst occurs, the electromagnetic radiation intensity near the sliding surface increases rapidly, the AE energy rises exponentially, and the energy released by microseismic events experiences at least one peak and is close to the next peak. At last, in situ investigations were performed at number 1412 coal face in the Huafeng Mine, China. Results showed that the signals patterns proposed are in good agreement with the process of the fault-slip type of rock burst. The pattern recognition can provide a basis for the early warning and the implementation of relief measures of the fault-slip type of rock burst.

Drilling cuttings method is a commonly used method to detect the risk of rockburst, which has been widely recognized and applied in coal mines. However, in the current theoretical research on the relationship between drilling cuttings method and coal stress, it is generally considered that the mechanical parameters of coal at different positions of roadway are unchanged, and the influence of surrounding rock plastic zone and elastic zone is not considered. Therefore, according to the secondary distribution characteristics of roadway side stress, the theoretical calculation formula of drilling cuttings in the plastic zone and elastic zone of the roadway side is established in this paper. The example shows that the distribution of cuttings on the roadway side is obviously consistent with the abutment pressure. The cuttings in the plastic zone and the elastic zone are in linear and power function with the coal stress, respectively, and the cuttings in the plastic zone are greater than those in the elastic zone. With the increase of the hole diameter, the slope of the relationship curve between the drill‐cutting weight and stress gradually increases, and the response of the drill‐cutting weight with a large hole diameter to the change of coal stress is more obvious. The numerical simulation results show that the error of the theoretical calculation formula of the drilling cuttings method is less than 9%, which can meet the engineering application needs of estimating the drill‐cutting weight in coal and the stress of coal. Using the theoretical formula, the stress field in the leading area of the working face is measured, and the leading influence range and the accurate position of the high stress concentration area are determined, which provides more comprehensive stress information for the early warning of impact danger and pressure relief.

The concentration of abutment pressure acting on coal seams induced by mining is a key factor to trigger rock burst. Understanding of abutment pressure or stress concentration is fundamental in preventing and controlling rock burst. The influence on abutment pressure fluctuation caused by the inhomogeneity of coal seams needs to be considered, but it is difficult to obtain by the present usual ways such as acoustic transmission, electromagnetic wave transmission, etc. In this article, the relationship between the amount of cuttings drilled in a coal seam and stress level was analyzed by considering the effect of drilling cutting expansion, and the drilling cutting test was carried out in Xinglongzhuang Coal Mine, Shandong Energy Ltd. It is found that the amount of cuttings drilled is positively related to the degree of stress concentration in both the plastic fracture zone and elastic zone. The amount of drilling cuttings is closely related to the roof weighting. In addition, the irregular fluctuation of drilling cuttings is an approximate map of distribution of stress concentration because of the non-uniformity of cracks and other defects in the coal seam. In order to meet the need of rock burst prevention by accurate pressure relief in high-stress zones, enough boreholes are needed.

In mining engineering, coal and gas outburst is extremely dangerous dynamic disaster, which will cause serious casualties and property losses. As a method to predict coal burst, the drilling cutting method has been widely used in coal mines. The drilling cutting weight is an important index of the drilling cutting method. In theoretical calculation, scholars usually assume that the coal is isotropic and homogeneous before drilling to deduce the formula of drilling cutting weight. However, in actual mining engineering, drilling cutting is usually carried out in the plastic coal body in front of the working face. Therefore, in the present study, the theoretical formula of the drilling cutting weight in the plastic coal mass is deduced, as well as in the elastic coal mass. The results show that the drilling cutting weight calculated based on the deduced formula increases with the increase of drilling depth in the plastic coal mass, which is consistent with the field measurement results. The fragmentation degrees of coal around the drilling hole are also considered by introducing cohesion, which changes linearly along the radial direction of the drilling hole. The results show that the smaller the cohesion, the greater the drilling cutting weight. The calculation formula for drilling cutting in elastic coal mass is also given. The dilatancy effect of coal around the drilling hole is also considered by introducing expansion coefficient n, which changes linearly along the radial direction of the drilling hole. There is a good match between the theoretical calculation results and the laboratory test results. The obtained results are helpful for the prediction and prevention of coal burst.

How to identify the stress generally in coal seam during borehole drilling process is a hot topic. In engineering, to obtain the stress state by drilling torque is very necessary. This study intends to obtain the stress state and machine drilling torque by numerical simulations. Finite element method (FEM) is employed to simulate the dynamical drilling process, considering variations in coal mechanical properties and drilling torque. Results show that the stress in coal seam is positively correlated with drilling torque and coal modulus of elasticity, with a notable inflection point in stress variation at a drilling depth of approximately 13 m. Two fitting relationship formula between stress and torque, elastic modulus, and drilling depth, in the range from 0 to 13 m and exceeding 13 m, were obtained. The study provides an inversion identification approach by monitoring drilling torque, and it is hopeful to be used for early warning rock burst during pressure relief by borehole drilling.