Gelatin is a natural biopolymer extensively used for tissue engineering applications due to its similarities to the native extracellular matrix. However, the rheological properties of gelatin formulations are not ideal for extrusion-based bioprinting. In this work, we present an approach to improve gelatin bioprinting performances by using pectin as a rheology modifier of gelatin and (3-glycidyloxypropyl)trimethoxysilane (GPTMS) as a gelatin–pectin crosslinking agent. The preparation of gelatin–pectin formulations is initially optimized to obtain homogenous gelatin–pectin gels. Since the use of GPTMS requires a drying step to induce the completion of the crosslinking reaction, microporous gelatin–pectin–GPTMS sponges are produced through freeze-drying, and the intrinsic properties of gelatin–pectin–GPTMS networks (e.g., porosity, pore size, degree of swelling, compressive modulus, and cell adhesion) are investigated. Subsequently, rheological investigations together with bioprinting assessments demonstrate the key role of pectin in increasing the viscosity and the yield stress of low viscous gelatin solutions. Water stable, three-dimensional, and self-supporting gelatin–pectin–GPTMS scaffolds with interconnected micro- and macroporosity are successfully obtained by combining extrusion-based bioprinting and freeze-drying. The proposed biofabrication approach does not require any additional temperature controller to further modulate the rheological properties of gelatin solutions and it could furthermore be extended to improve the bioprintability of other biopolymers.

Poultry feathers are among the most abundant and polluting keratin-rich waste biomasses. In this work, we developed a one-pot microwave-assisted process for eco-friendly keratin extraction from poultry feathers followed by a direct electrospinning (ES) of the raw extract, without further purification, to obtain keratin-based bioplastics. This microwave-assisted keratin extraction (MAE) was conducted in acetic acid 70% v/v. The effects of extraction time, solvent/feathers ratio, and heating mode (MAE vs. conventional heating) on the extraction yield were investigated. The highest keratin yield (26 ± 1% w/w with respect to initial feathers) was obtained after 5 h of MAE. Waste-derived keratin were blended with gelatin to fabricate keratin-based biodegradable and biocompatible bioplastics via ES, using 3-(Glycidyloxypropyl)trimethoxysilane (GPTMS) as a cross-linking agent. A full characterization of their thermal, mechanical, and barrier properties was performed by differential scanning calorimetry, thermogravimetric analysis, uniaxial tensile tests, and water permeability measurements. Their morphology and protein structure were investigated using scanning electron microscopy and attenuated total reflection-infrared spectroscopy. All these characterizations highlighted that the properties of the keratin-based bioplastics can be modulated by changing keratin and GPTMS concentrations. These bioplastics could be applied in areas such as bio-packaging and filtration/purification membranes.

The biomass waste obtained at the end-of-pipe of the extraction industry can be used as fuel for energy production, aiming at cost reduction/waste disposal issues. However, few systematic investigations into the calorific value of these residues are reported in the literature. In this work, the thermochemical properties of solid residues from different biomasses (residues from citrus peels, leaves, flowers, stems, and poultry feathers used for extraction) as potential biomass fuels have been investigated. The heat of combustion (Δ_cH) of the solid residues from citrus (orange, tangerine, lemon, grapefruit, and pomelo), aromatic herbs (rosemary, lavender, thyme, Artemisia vulgaris L. and Ruta chalepensis L.), and poultry feathers biomasses was measured by direct calorimetry. The results were compared with the higher heating values (HHV) calculated using the elemental (CHNOS) and thermogravimetric (TGA) analyses data and with the enthalpy of combustion calculated using the biomass composition predicted by FTIR spectroscopy in tandem with chemometrics. The calculated values match with the corresponding experimental values of Δ_cH. The heat of combustion highlights the energetic features of solid residues for their potential uses as alternative biomass for energy production. This information is essential to evaluate the employment of solid residues as fossil fuel substitutes.