Kezhen Han

Dr. Kezhen Han

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2018 in IET Control Theory & Applications
Verified
Journal Article
Open access
PDF file
KHKezhen Han
Kezhen Han
JFJian Feng
Jian Feng
YLYueyang Li
Yueyang Li
SLShi Li
Shi Li
In this study, an integrated fault tolerant preview tracking control framework is proposed based on reduced‐order simultaneous state and fault estimation, robust preview control and fault signal compensation. In general, this work consists of three key design parts. Firstly, the analysis and synthesis conditions of a novel reduced‐order simultaneous state and fault estimator are given based on the equivalent model reconstruction and optimisation of the parametric solution. Note that such a reduced‐order design method can avoid traditional output equation reduction requirement, and has a wider application scope. Secondly, the robust preview tracking control policy is constructed by integrating state‐feedback, preview action, and integral operation. Relying on augmentation modelling technique, a linear quadratic preview control design problem is transformed into an equivalent augmented state‐feedback control design problem. Thirdly, the fault compensation is achieved by using estimated fault to accommodate fault influence. These involved designs are performed at the optimisation level, and thus guarantee the robust tracking performance of closed‐loop systems. The effectiveness of the above conclusions is finally verified via two case studies.


6 August 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
KHKezhen Han
Kezhen Han
JFJian Feng
Jian Feng
QZQing Zhao
Qing Zhao
PJPing Jiang
Ping Jiang
XWXiaohong Wang
Xiaohong Wang
This article proposes some new improvements to the traditional constrained predictive fault-tolerant control (FTC) method by enlarging the maximal fault-tolerant admissible region and reducing the online computational complexity. In general, the generalized parameterization of predictive input and event-triggered predictive regulation are integrated into a framework of fault compensation-based dual-mode tube predictive FTC. This predictive FTC scheme has three notable characteristics: 1) The dual-mode FTC consisting of fixed-mode fault compensation and freely predictive adjustments allows most of the calculations to be predetermined offline, while only a simple optimization problem requires to be solved online; 2) the fault-tolerant ability is enhanced by utilizing generalized parameterization of predictive inputs to enlarge the region of attraction of a faulty system; 3) the real-time computational effort of predictive FTC is further reduced by constructing an event-triggered condition to avoid unnecessary online predictive optimization. A case study of a practical synchronous dc–dc Buck converter is given to validate the effectiveness of the proposed predictive FTC method.

1 March 2019 in International Journal of Control
Verified
Journal Article
Closed access
KHKezhen Han
Kezhen Han
JFJian Feng
Jian Feng
In this paper, we propose a data-driven robust fault tolerant preview control scheme for discrete-time LTI systems with completely unknown dynamics. In general, this work consists of three key design parts. Firstly, the Markov parameters sequence is identified to extract system feature from data. Then, robust linear quadratic preview control policy composed of finite data feedback, integral operation and preview action is designed through establishing data-space characterisation and solving the related convex optimisation problem. Thirdly, an active fault tolerant method composed of fault detection, isolation, estimation and corresponding compensation is further constructed to accommodate fault influence. Note that all these involved designs are performed at Markov parameters sequence level. Thus above integrated preview control scheme can avoid the priori knowledge requirements including system matrices, order, and state variables. The effectiveness of the obtained results is finally verified via a case study of the injection moulding machine.

21 July 2021 in Entropy
Verified
Journal Article
Open access
PDF file
KHKezhen Han
Kezhen Han
CCChangzhi Chen
Changzhi Chen
MCMengdi Chen
Mengdi Chen
ZWZipeng Wang
Zipeng Wang
A new active fault tolerant control scheme based on active fault diagnosis is proposed to address the component/actuator faults for systems with state and input constraints. Firstly, the active fault diagnosis is composed of diagnostic observers, constant auxiliary signals, and separation hyperplanes, all of which are designed offline. In online applications, only a single diagnostic observer is activated to achieve fault detection and isolation. Compared with the traditional multi-observer parallel diagnosis methods, such a design is beneficial to improve the diagnostic efficiency. Secondly, the active fault tolerant control is composed of outer fault tolerant control, inner fault tolerant control and a linear-programming-based interpolation control algorithm. The inner fault tolerant control is determined offline and satisfies the prescribed optimal control performance requirement. The outer fault tolerant control is used to enlarge the feasible region, and it needs to be determined online together with the interpolation optimization. In online applications, the updated state estimates trigger the adjustment of the interpolation algorithm, which in turn enables control reconfiguration by implicitly optimizing the dynamic convex combination of outer fault tolerant control and inner fault tolerant control. This control scheme contributes to further reducing the computational effort of traditional constrained predictive fault tolerant control methods. In addition, each pair of inner fault tolerant control and diagnostic observer is designed integratedly to suppress the robust interaction influences between estimation error and control error. The soft constraint method is further integrated to handle some cases that lead to constraint violations. The effectiveness of these designs is finally validated by a case study of a wastewater treatment plant model.

2 May 2022 in IEEE Transactions on Systems, Man, and Cybernetics: Systems
Verified
Journal Article
Closed access
KHKezhen Han
Kezhen Han
JFJian Feng
Jian Feng
YLYueyang Li
Yueyang Li
PJPing Jiang
Ping Jiang
XWXiaohong Wang
Xiaohong Wang
This article presents some new improvements to the relevant constrained predictive fault-tolerant tracking control (FTTC) methods through embedding optimal preview regulation and reference governance. The main novelty of such a strategy is that some valuable information of finite future references can be adequately scheduled to optimize the robust tracking performance and significantly enlarge the fault-tolerant admissible region. In order to better describe the wide applicability of the proposed strategy, the robust FTTC problem for a class of LPV systems with state/input constraints is considered. Overall, the involved key designs consist of three parts. First, an unconstrained FTTC component is constructed by combining tracking error feedback, reference input regulation, and fault signal compensation. It is used to guarantee the robust tracking stability of closed-loop systems when the constraints are not activated. Second, a tube-based predictive FTTC policy with an embedded optimal preview regulator is designed to achieve the robust constraint satisfaction and transient response improvement. Third, an embedded reference governor is additionally integrated to significantly enlarge the size of the fault-tolerant admissible region. This design further reinforces the feasibility of constrained FTTC optimization. The effectiveness of these results is finally validated by a case study of a single transistor dc/dc Forward converter.