Hyesung Na

Mr. Hyesung Na

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 January 2018 in Metals
Verified
Journal Article
Open access
PDF file
HNHyesung Na
Hyesung Na
BKByung-Hoon Kim
Byung-Hoon Kim
SLSang-Hoon Lee
Sang-Hoon Lee
CKChung-Yun Kang
Chung-Yun Kang
In the 21st century, there is an increasing need for high-capacity, high-efficiency, and environmentally friendly power generation systems. The environmentally friendly integrated gasification combined-cycle (IGCC) technology has received particular attention. IGCC pressure vessels require a high-temperature strength and creep strength exceeding those of existing pressure vessels because the operating temperature of the reactor is increased for improved capacity and efficiency. Therefore, high-pressure vessels with thicker walls than those in existing pressure vessels (≤200 mm) must be designed. The primary focus of this research is the development of an IGCC pressure vessel with a fully bainitic structure in the middle portion of the 300 mm thick Cr-Mo steel walls. For this purpose, the effects of the alloy content and cooling rates on the ferrite precipitation and phase transformation behaviors were investigated using JMatPro modeling and thermodynamic calculation; the results were then optimized. Candidate alloys from the simulated results were tested experimentally.

17 March 2025 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
DKDong Young Kwon
Dong Young Kwon
HNHyesung Na
Hyesung Na
JCJae-Young Choi
Jae-Young Choi
JKJee-Hyun Kang
Jee-Hyun Kang

23 May 2018 in Metals
Verified
Journal Article
Open access
PDF file
HNHyesung Na
Hyesung Na
SLSanghoon Lee
Sanghoon Lee
CKChung-Yun Kang
Chung-Yun Kang
2.25Cr-1Mo steel with high strength at high temperatures and superior hydrogen resistance is widely used as power generation boiler material in high-temperature and high-pressure environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 386 and 28J, which are drastically different values. The analysis of the fracture surface of the 28J test specimen revealed MnS inclusions and it was found that cracks were initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 386J impact specimen. However, the volume fraction of the inclusions was significantly less than that of the 28J specimen. It was also found that the ferrite and carbide content of the 386J specimen was less than the 28J specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation such as MnS inclusions on ferrite and carbide were compared and analyzed.

9 November 2017 in Metals
Verified
Journal Article
Open access
PDF file
HSHee Joon Sung
Hee Joon Sung
HNHyesung Na
Hyesung Na
HSHee Joon Sung
Hee Joon Sung
The importance of the additional growth and/or transformation of the austenite phase that occurs in weld metals of super duplex stainless steel upon reheating is known. However, the effects have not been fully investigated, especially with respect to reheating induced by weaving during single-pass welding. In this work, bead-on-pipe gas tungsten arc welding (GTAW) was conducted on super duplex stainless steel to understand the effect of weaving on the microstructure of weld metal. Microstructural analysis, electron backscatter diffraction (EBSD), and focused ion beam transmission electron microscopy (FIB-TEM) were carried out to investigate the relationship between weaving and microstructural change. The weaving of GTAW produced a dynamic reheated area just before the weld bead during welding. It was revealed that extensive reheated weld existed even after one welding pass, and that the content of the austenite phase in the reheated area was higher than that in the non-reheated area, indicating the existence of a large quantity of intragranular austenite phase. In addition, the Cr2N content in the reheated area was lower than that in the non-reheated area. This reduction of Cr2N was closely related to the reheating resulting from weaving. TEM analysis revealed that Cr2N in the non-reheated area was dispersed following heating and transformed to secondary austenite.

14 May 2018 in Preprints.org
Verified
Preprint
Open access
HNHyesung Na
Hyesung Na
SLSanghoon Lee
Sanghoon Lee
CKChungyun Kang
Chungyun Kang
2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

1 May 2018 in Metals
Verified
Journal Article
Open access
PDF file
HSHee Joon Sung
Hee Joon Sung
HNHyesung Na
Hyesung Na
CKChung-Yun Kang
Chung-Yun Kang
Gas tungsten arc welding (GTAW) with three different heat inputs controlled by the weaving width was performed to understand their effects on the microstructural changes during bead-on-pipe welding of super duplex stainless steel. The microstructure of the weld metals was categorized into three different types of zones: non-reheated, reheated type, and reheating-free zone. Even though single-pass welding with different weaving widths was employed, a reheated microstructure was detected, which has been previously observed with multiple pass welding. This phenomenon was called “dynamic reheating”, because it was produced by the weaving operation during welding regardless of the weaving width. The categorized area fraction varied with the weaving width change. Electron backscatter diffraction (EBSD) results at the edge (the area near the fusion line) of the low-heat-input condition indicated a higher austenite volume fraction and a lower Cr2N fraction than that of the medium heat input condition. Thus, it described an inverse relationship, because higher heat input provided a lower austenite fraction. In addition, it was observed clearly that the austenite fraction at the medium heat input condition was dramatically increased by reheating, while the Cr2N fraction was reduced. Regardless of the weaving width, reheating contributed to the increase of the austenite fraction, further reducing the Cr2N quantity. The edge areas in the map showed an inverse relationship in the reheated area fraction between low heat input and medium heat input. For this reason, the austenite fraction on the weld metal was determined not only by the heat input, but also by the amount of reheating.