A new approach has been proposed to determine ocean subsurface particulate backscattering coefficient bbp from CALIOP 30° off-nadir lidar measurements. The new method also provides estimates of the particle volume scattering function at the 180° scattering angle. The CALIOP based layer-integrated lidar backscatter and particulate backscattering coefficients are compared with the results obtained from MODIS ocean color measurements. The comparison analysis shows that ocean subsurface lidar backscatter and particulate backscattering coefficient bbp can be accurately obtained from CALIOP lidar measurements, thereby supporting the use of space-borne lidar measurements for ocean subsurface studies.
Remote sensing from Earth‐observing satellites is now providing valuable information about ocean phytoplankton distributions. This paper presents the new ocean subsurface optical properties obtained from two space‐based lidars: the Cloud‐Aerosol Lidar with Orthogonal Polarization (CALIOP) aboard the Cloud‐Aerosol Lidar and Infrared Pathfinder Satellite Observations satellite and the Advanced Topographic Laser Altimeter System (ATLAS) aboard the Ice, Cloud, and land Elevation Satellite‐2 satellite. Obtaining reliable estimates of subsurface biomass necessitates removing instrument artifacts peculiar to each sensor, that is, polarization crosstalk artifacts in the CALIOP signals and after pulsing effects arising from the ATLAS photodetectors. We validate the optical properties derived from the corrected lidar backscatter signals using MODerate‐resolution Imaging Spectroradiometer ocean color measurements and autonomous biogeochemical Argo float profiles. Our results support the continued use of present and future spaceborne lidars to study the global plankton system and characterize its vertical structures in the upper ocean.
The Advanced Topographic Laser Altimeter System (ATLAS) aboard the Ice, Cloud, and land Elevation Satellite‐2 (ICESat‐2) has been making very high resolution measurements of the Earth’s surface elevation since October 2018. ATLAS uses photomultiplier tubes (PMTs) as detectors in photon counting mode, so that a single photon reflected back to the receiver triggers a detection within the ICESat‐2 data acquisition system. However, one characteristic of ICESat‐2 detected photons is the possible presence of afterpulses, defined as small amplitude pulses occurring after the primary signal pulse due to photon arrival. The disadvantage of these afterpulses is that they often confound the accurate measurements of low level signals following a large amplitude of signal and can degrade energy resolution and cause errors in pulse counting applications. This paper discusses and summarizes the after‐pulsing effects exhibited by the ATLAS PMTs based on on‐orbit measurements over different seasons and geographic regions. The potential impacts of these after‐pulsing effects on altimetry and ocean subsurface retrievals are discussed.
Detection of subsurface returns from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) satellite were demonstrated. Despite the coarse range resolution of this aerosol lidar, evidence of subsurface scattering was observed as a delay and broadening of the cross-polarized signal relative to the co-polarized signal in the three near-surface range bins. These two effects contributed to an increased depolarization at the nominal depth of 25 m. These features were all correlated with near-surface chlorophyll concentrations. An increase in the depolarization was also seen at a depth of 50 m under certain conditions, suggesting that chlorophyll concentration at that depth could be estimated if an appropriate retrieval technique can be developed. At greater depths, the signal is dominated by the temporal response of the detectors, which was approximated by an analytical expression. The depolarization caused by aerosols in the atmosphere was calculated and eliminated as a possible artifact.
The application of diffusion theory and Monte Carlo lidar radiative transfer simulations presented in Part I of this series of study suggests that snow depth can be derived from the first-, second- and third-order moments of the lidar backscattering pathlength distribution. These methods are now applied to the satellite ICESat-2 lidar measurements over the Arctic sea ice and land surfaces of Northern Hemisphere. Over the Arctic sea ice, the ICESat-2 retrieved snow depths agree well with co-located IceBridge snow radar measured values with a root-mean-square (RMS) difference of 7.8 cm or 29.2% of the mean snow depth. The terrestrial snow depths derived from ICESat-2 show drastic spatial variation of the snowpack along ICESat-2 ground tracks over the Northern Hemisphere, which are consistent with the University of Arizona (UA) and Canadian Meteorological Centre (CMC) gridded daily snow products. The RMS difference in snow depths between ICESat-2 and UA gridded daily snow products is 14 cm, or 28% of the mean UA snow depth. To better understand these results, we also discuss the possible sources of errors in ICESat-2 derived snow depths, including surface roughness within the laser footprint, atmospheric forward scattering, solar background noise, and detector dark current. Simulation results indicate that the snow depth errors would be less than 5 cm if the standard deviation of pulse spreading due to surface roughness is within 50 cm. Our results demonstrate that the ICESat-2 lidar measurements can be used to reliably derive snow depth, which is a critical geophysical parameter for cryosphere studies including sea ice thickness estimation and also provides important constraints in the modeling of terrestrial hydrological processes.
With the advancement of Lidar technology, bottom depth ( ) of optically shallow waters (OSW) can be measured accurately with an airborne or space-borne Lidar system ( hereafter), but this data product consists of a line format, rather than the desired charts or maps, particularly when the Lidar system is on a satellite. Meanwhile, radiometric measurements from multiband imagers can also be used to infer ( hereafter) of OSW with variable accuracy, though a map of bottom depth can be obtained. It is logical and advantageous to use the two data sources from collocated measurements to generate a more accurate bathymetry map of OSW, where usually image-specific empirical algorithms are developed and applied. Here, after an overview of both the empirical and semianalytical algorithms for the estimation of from multiband imagers, we emphasize that the uncertainty of varies spatially, although it is straightforward to draw regressions between and radiometric data for the generation of . Further, we present a prototype system to map the confidence of pixel-wise, which has been lacking until today in the practices of passive remote sensing of bathymetry. We advocate the generation of a confidence measure in parallel with , which is important and urgent for broad user communities.