Yu Xie

Dr. Yu Xie

School of Mechanical Engineering and Automation, Fuzhou University, Fuzhou, Fujian, China
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 July 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
YXYu Xie
Yu Xie
QFQi Fang
Qi Fang
HZHan Zhao
Han Zhao
YLYang Li
Yang Li
ZLZhihai LIN
Zhihai LIN
JCJianxiong Chen
Jianxiong Chen
Melt electrospinning writing is a new and promising method for fabricating micro/nanofibers, which has shown great prospects in the biomedical fields such as 3D printing of porous scaffolds. The diameter of the melt electrospinning writing fiber can determine the resolution of the microstructure; thus, the controllability of the fiber diameter is of great significance to the whole fabrication process. In this paper, an orthogonal design experiment (six factors, three levels) was used to explore the impacts of six melt electrospinning parameters (melt temperature, collector speed, tip-to-collector distance, melt flow rate, voltage, and needle gauge) on the fiber diameter. In this experiment, the diameter of fibers obtained with the designed experimental parameters and conditions varied from 10.30 μm to 20.02 μm. The range analysis of orthogonal test results showed that the melt flow rate was the most important factor influencing the diameter of melt electrospinning writing fiber, while the voltage was the least influential factor. The variance analysis of orthogonal test results showed that melt temperature, collector velocity, tip-to-collector distance and melt flow rate had a significant influence on the diameter of melt electrospinning writing fiber. On the basis of the first-order regression equation, the fiber diameter of poly-ε-caprolactone can be accurately controlled, thus improving the engineering applications of poly-ε-caprolactone.

12 October 2023 in Energies
Verified
Journal Article
Open access
PDF file
ZLZhe Lu
Zhe Lu
SLShuwen Lin
Shuwen Lin
JCJianxiong Chen
Jianxiong Chen
TGTianqi Gu
Tianqi Gu
YXYu Xie
Yu Xie
To address the limitation of existing excavator optimization methods, which primarily focus on the force performance while neglecting energy consumption and fail to realize environmentally friendly and low-carbon designs, this paper proposes a new multi-objective collaborative optimization method for an excavator to reduce energy consumption during the working process while maintaining optimal performance. By formulating a mathematical model that quantifies the energy consumption during the working process, this paper optimizes the working conditions by analyzing the energy consumption characteristics under typical working conditions. To overcome the limitation of existing linear weighting methods in multi-objective optimization, such as imbalanced optimization quality among sub-objectives, this paper proposes a new modeling approach based on the loss degree of sub-objectives. A multi-objective collaborative optimization model for the excavator with reduced energy consumption is established, and a corresponding multi-objective collaborative optimization algorithm is developed and applied to achieve optimal solutions for sub-objectives. The optimization results demonstrate that applying the new multi-objective collaborative optimization method to the excavator achieves better optimization quality than traditional methods. It also provides a more balanced improvement in the optimization values of each sub-objective, resulting in a significant reduction in the energy consumption of the excavator during operation.

1 December 2020 in Theoretical and Applied Fracture Mechanics
Verified
Journal Article
Closed access
HYH. Yuan
H. Yuan
YXYu Xie
Yu Xie

14 January 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
YXYu Xie
Yu Xie
YCYixiong Chen
Yixiong Chen
HXHang Xu
Hang Xu
JCJianxiong Chen
Jianxiong Chen
To improve the fabrication efficiency of the two-photon polymerization (TPP) laser direct writing, the TPP exposure process was set to complete by a single-line scan, which was named 2D TPP. The voxel of the 2D TPP should be large enough to cross the photoresist and the underlayer. To explore the resolution limit of the 2D TPP considering the thickness of the photoresist, a new method named the 45° scanning method was proposed. Meanwhile, a two-photon micro-nano fabrication platform was developed. A group of experiments based on the orthogonal decomposition method was carried out to analyze the width and length of the voxel on the S1805 photoresist under different laser power and processing speed. To confirm whether the resolution of the micro-nano structures fabricated by 2D TPP is consistent with the width of the voxel, aluminum wire grids were fabricated through the 2D TPP and the metal lift-off process. A second-order regression equation of the machining resolution and input parameters of the 2D TPP is deduced. The correlation coefficient between the width of the voxel and the aluminum wire grids is 0.961, which means a significant positive correlation between them. Finally, the second-order regression model derived from the fabrication resolution of the 2D TPP was validated by experiments. Full 2D grids were fabricated using 2D TPP and mental lift-off process. This paper provides a convenient, low-cost, and high-efficiency method for calibrating the fabrication resolution of 2D TPP on various photoresists.

25 August 2024 in Materials
Verified
Journal Article
Open access
PDF file
QYQingan Yin
Qingan Yin
HCHui Chen
Hui Chen
JCJianxiong Chen
Jianxiong Chen
YXYu Xie
Yu Xie
MSMing Shen
Ming Shen
YHYuhua Huang
Yuhua Huang
Due to its exceptional mechanical and chemical properties at high temperatures, Inconel 718 is extensively utilized in industries such as aerospace, aviation, and marine. Investigating the flow behavior of Inconel 718 under high strain rates and high temperatures is vital for comprehending the dynamic characteristics of the material in manufacturing processes. This paper introduces a physics-based constitutive model that accounts for dislocation motion and its density evolution, capable of simulating the plastic behavior of Inconel 718 during large strain deformations caused by machining processes. Utilizing a microstructure-based flow stress model, the machinability of Inconel 718 in terms of cutting forces and temperatures is quantitatively predicted and compared with results from orthogonal cutting experiments. The model’s predictive precision, with a margin of error between 5 and 8%, ensures reliable consistency and enhances our comprehension of the high-speed machining dynamics of Inconel 718 components.

12 October 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
YSYongGui Shi
YongGui Shi
ZLZhihai LIN
Zhihai LIN
TWTianran Wang
Tianran Wang
HCHuang Chaokai
Huang Chaokai
HCHui Chen
Hui Chen
YXYu Xie
Yu Xie
Micro-polarizer array (MPA) is the core optical component of the Division of Focal-Plane (DoFP) imaging system, and its design is very important to the system’s performance. Traditional design methods rely on theoretical analysis and simulation, which is complicated and requires designers to have profound theoretical foundations. In order to simplify the design process and improve efficiency, this paper proposes a 2 × 2 MPA reverse-design strategy based on particle swarm optimization (PSO). This strategy uses intelligent algorithms to automatically explore the design space in order to discover MPA structures with optimal optical properties. In addition, the all-pass filter is introduced to the MPA superpixel unit in the design, which effectively reduces the crosstalk and frequency aliasing between pixels. In this study, two MPA models were designed: a traditional MPA and an MPA with an all-pass filter. The Degree of Linear Polarization (DOLP) image contrast is used as the evaluation standard and compared with the traditional MPA; the results show that the contrast of the newly designed traditional MPA image is increased by 21%, and the MPA image with the all-pass filter is significantly increased by 82%. Therefore, the reverse-design method proposed in this paper not only simplifies the design process but also can design an MPA with enhanced optical performance, which has obvious advantages over the traditional method.