Near‐infrared organic photodetectors (NIR OPDs) comprising ultra‐narrow bandgap non‐fullerene acceptors (NFA, over 1000 nm) typically exhibit high dark current density under applied reverse bias. Therefore, suppression of dark current density is crucial to achieve high‐performance of such NIR OPDs. Herein, cyano (CN) with a strong electron‐withdrawing property is introduced into alkoxy thiophene as a π‐bridge to adjust its optoelectronic characteristics, and the correlation between dark current density and charge injection barrier is investigated. Compared with their motivated NFA (COTH), the novel CN‐substituted NFAs, COTCN and COTCN2, exhibited deeper‐lying highest occupied molecular orbital energy levels and narrower optical bandgap (<1.10 eV), owing to the strong inductive and resonance effect of CN. The dark current and total noise currents are minimized as the number of substituted CN increases because of the larger hole injection barrier. Consequently, PTB7‐Th:COTCN2 exhibited the best shot‐noise limited detectivity (D*sh, 1.18 × 1012 Jones) and total noise detectivity (D*n, 1.33 × 1011 Jones) compared with those of PTB7‐Th:COTH (D*sh, 2.47 × 1011 Jones and D*n, 1.96 × 1010 Jones).
Organic photodetectors (OPDs) based on non‐fullerene acceptors (NFAs) have received considerable attention because of their potential for use in various commercial applications as near‐infrared (NIR) light sensing platforms. However, recent OPDs suffer from low NIR photoresponse and large dark/noise currents with narrow bandgap organic photoactive materials. Herein, a π‐bridge molecular engineering strategy replacing alkoxythienyl with benzothiadiazole for ultra‐narrow bandgap (ultra‐NBG) NFAs is designed to achieve simultaneously high photoresponse at NIR region and low noise current density, thereby leading to excellent NIR (≈1050 nm) detectivity (D*). The newly synthesized ultra‐NBG NFAs, namely COB and CBT with optical bandgaps below 1.14 eV, present high responsivity (R) with 0.369 and 0.080 A W−1, respectively, at a wavelength of 1050 nm. Especially, with effectively suppressed noise current density, COB‐based OPD exhibits a high NIR (≈1050 nm) D* value of 2.18 × 1011 cm Hz1/2 W−1 at −0.5 V bias. The obtained R and D* values for these NFAs exceed or are comparable to those of a commercial Si photodetector at 1050 nm. This work provides important insight into the π‐bridge molecular engineering strategy for ultra‐NBG NFAs, which facilitate achieving highly sensitive NIR OPDs with high NIR photoresponse and low dark/noise current.
1 October 2010 in Journal of Mechanical Science and Technology
In this article, we report the development of inkjet printing technique for the fabrication of bulk heterojunction organic photovoltaic cells (OPVs). We have demonstrated highly efficient OPV with a mixture of poly(3-hexylthiophene)s (P3HT) and 1-[3-(methoxycarbonyl)propyl]-1-phenyl[6.6]C61 (PCBM) as an inkjet-printed photoactive layer. Especially, 3.8% of power conversion efficiency (PCE) and 0.68 V of open circuit voltage (Voc) can be obtained by using the chlorobenzene as a solvent. This value is the highest performance in P3HT:PCBM based OPV system by now. We reveal that substantial improvements can be realized by nano-structured heterojunction after inkjet printing and this technique is one of the promising fabrication methods for organic photovoltaic cells. Also, we have designed and fabricated five-series connected large area (18 cm2) inkjet-printed OPVs using the patterned indium tin oxide (ITO) with Au bus-electrode to minimize the efficiency drop due to the surface resistance of ITO. Consequently, 1.25% of power conversion efficiency can be obtained with a short circuit current of 1.24 mA/cm2, a fill factor of 0.32, and an open circuit voltage of 3.2 V.
The occurrence of low-frequency instability (LFI) appears to be related to multiple interactions among many complex physical processes, such as vortex shedding, boundary-layer oscillation, and additional combustion in the post-combustion chamber. In this study, two combustion tests were conducted to suppress LFI and to examine which physical processes its occurrence was most sensitive. In the first test, two fuel inserts were used to modify the formation of a boundary layer, vortex shedding at the end of the fuel, and vortex impingement. In the second test, the fuel insert located at the front end was replaced with swirl injection. The first test was aimed at controlling and suppressing the initiation of LFI using fuel inserts, through which a small step appeared gradually due to differences in the regression rates of the two materials, i.e., polymethyl methacrylate and high-density polyethylene. The test results confirmed that (i) there are physical connections among several processes, such as the thermoacoustic coupling between p′and q′ and the oscillations of the upstream boundary flow, and (ii) LFI suppression is possible by disrupting or eliminating the connections among these physical processes. The second test was also aimed to control LFI while minimizing the deviation in combustion performance using proper swirl injection along with a fuel insert. Even when replaced by swirl injection, LFI suppression was still possible and showed reasonable combustion performance without causing too much deviation from the baseline in terms of the oxygen-to-fuel ratio and the fuel regression rate.