Jordy Santana-Villamar

Mr. Jordy Santana-Villamar

Escuela Superior Politecnica del Litoral, Guayaquil, Guayas, Ecuador
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 August 2020 in Frontiers in Energy Research
Verified
Journal Article
Open access
PDF file
Jordy Santana-VillamarJordy Santana-Villamar
Jordy Santana-Villamar
Mayken Espinoza-AndaluzMayken Espinoza-Andaluz
Mayken Espinoza-Andaluz
TLTingshuai Li
Tingshuai Li
MAMartin Andersson
Martin Andersson
Polymer electrolyte fuel cells (PEFCs) have shown a great potential to be used in several applications, e.g., portable, mobile and stationary systems. Each of the mentioned applications demands from PEFCs different operating conditions to perform in the best possible manner. Knowing in detail the behavior of their internal components will help to improve the mechanical and thermal properties of the different constitutive layers. The objective of this research is to analyze in detail the behavior of the internal resistances of a PEFC, using the impedance spectroscopy technique. A single cell is evaluated in a broad range of current densities, i.e., from 0.2 to 2.0 A.cm–2, to evaluate the resistances that cause loss of performance. The analyzed resistances correspond to the ohmic, charge transfer and mass transport resistance. The results were obtained after the interpretation of the data taking from Nyquist diagrams, and they were analyzed considering high and low conditions of relative humidity (RH). The obtained results showed that the ohmic resistance (attributed to membrane Nafion® 212), is independent of the load applied for fully humidified conditions, with a value of 0.0725 Ω.cm2. On the other hand, it is strongly dependent on low humidification conditions, with values between [0.198–0.132] Ω.cm2, for current density of [0.2–2.0] A.cm–2, respectively. It was also found that the charge transfer resistance decreases with respect to the applied load until a saturation value, and further it represents the major participation to the total resistance of the cell. The charge transfer resistance represents around 50–75% of the total resistance in conditions of high RH, and among 30–65% for conditions of low RH. In addition, it was found that the mass transport resistance appears early at low RH and triples for full humidification conditions.

13 January 2020 in ECS Transactions
Verified
Journal Article
Closed access
Jordy Santana-VillamarJordy Santana-Villamar
Jordy Santana-Villamar
MEMayken Espinoza-Andaluz
Mayken Espinoza-Andaluz
GVGary Villon
Gary Villon
YQYuanxin Qi
Yuanxin Qi
TLTingshuai Li
Tingshuai Li
MAMartin Andersson
Martin Andersson
A polymer electrolyte fuel cell (PEFC) is an electrochemical device that converts the chemical energy presents in the hydrogen into electricity and heat having as by product only water. The energy conversion process is carried out in a clean and noiseless manner. Depending on the applications, a PEFC works at different operating temperature. In this study, the internal resistance of a PEFC is evaluated by using Electrochemical Impedance Spectroscopy (EIS) at moderate low current density, i.e., 0.5 A/cm2, in the temperature range of 40 – 80°C. The evaluation is carried out considering frequencies between 3.1kHz and 1Hz. An equivalent Randle circuit is considered as adjusted model and the Nyquist and Bode diagram were obtained to analyze the internal resistance. Results show that the ohmic resistance and charge transport increase when the operating temperature is low, decreasing the cell performance. A voltage drop of 42 mV was obtained for the evaluated temperature sweep. At the same time, it was demonstrated that the double layer capacitance increases at high temperatures, increasing its operating performance.

1 November 2020 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
Mayken Espinoza-AndaluzMayken Espinoza-Andaluz
Mayken Espinoza-Andaluz
Jordy Santana-VillamarJordy Santana-Villamar
Jordy Santana-Villamar
MAMartin Andersson
Martin Andersson

14 August 2024 in Materials Advances
Verified
Journal Article
Open access
PDF file
Jordy Santana-VillamarJordy Santana-Villamar
Jordy Santana-Villamar
MCMiguel Carrasco-Cordero
Miguel Carrasco-Cordero
JSJose Suarez-Loor
Jose Suarez-Loor
Mayken Espinoza-AndaluzMayken Espinoza-Andaluz
Mayken Espinoza-Andaluz
ARAndres Rigail
Andres Rigail
Bipolar plates (BPs) based on a polymer matrix and carbon materials have lately been considered potential alternatives in fabricating polymer electrolyte fuel cell (PEFC) components. For widespread market adoption, utilizing minimal energy in the synthesis process and abstaining from harmful solvents is crucial. This study proposes an efficient, solventless method to address these limitations, emphasizing low-viscosity epoxy resin and high-expansion ratio graphite as critical parameters to fabricate highly conductive composites suitable for bipolar plate applications. To achieve this, high-quality expanded graphite (EG) was prepared using microwave heating, oxygen removal, and sieving for particle size control. The EG was then mixed with a commercial DGEBA-based resin in proportions of 40, 50, and 60 wt%, hot-molded at 110 °C with 4500 psi for 10 min, followed by post-curing at 130 °C, for an additional 10 minutes. The resulting composites were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), flexural strength testing, and in-plane electrical conductivity measurements. The properties obtained were compared with the requirements set by the U.S. Department of Energy (DOE). XRD and SEM revealed an amorphous, highly porous EG filler with limited dispersion, particularly at high EG concentrations, 60 wt%. Despite this, a remarkable electrical conductivity of 177.99 S cm−1 was achieved at 60 wt% EG, without using any solvent or secondary filler, and most of the composites surpassed DOE's flexural strength requirement, 25 MPa. This methodology demonstrates a solventless approach for producing high-performance BPs composites that meet or exceed DOE's electrical and mechanical property requirements for PEFC applications.

1 June 2021 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
Jordy Santana-VillamarJordy Santana-Villamar
Jordy Santana-Villamar
RRRaúl Reyna
Raúl Reyna
ARAndrés F. Rigail-Cedeño
Andrés F. Rigail-Cedeño
Mayken Espinoza-AndaluzMayken Espinoza-Andaluz
Mayken Espinoza-Andaluz
Polymer Electrolyte Fuel Cell (PEFC) is an environmentally friendly device that generates electricity with zero emissions. A constitutive part of PEFCs is the bipolar plate (BP), which offers mechanical support and distributes its reactant gases. In relation, manufacturing electrically conductive BPs at low cost is needed to position PEFC technology on the market. This work summarizes the processing methods of Epoxy-graphite based compounds in order to get better-synthetized samples. First, the applying of an epoxy-amine matrix composed of bisphenol A diglycidyl ether (DGEBA) and aliphatic triglycidyl ether epoxy resins cured with a polyether triamine is presented. Next, two different preparations to obtain high quality expanded graphite focuses on an appropriate graphite exfoliation were evaluated. Subsequently, three processes from graphite-resin compounds synthesis are detailed and analyzed based on Energy Dispersive X-ray Spectroscopy (EDS), Scanning Electron Microscopy (SEM), electrical conductivity tests, and particle size characterization. Besides, the effect of using different secondary fillers such as Carbon Black (CB), Graphite nanoplatelets (N99), and graphene (GR) is shown, concluding that the greater electrical conductivity is obtained using graphene in low percentages (0.5%), reaching 65.39 s.cm −1 . Finally, a functional method of compression and extraction to avoid damage to the specimen is proposed.

7 September 2021 in Energies
Verified
Journal Article
Open access
PDF file
Ángel Encalada-DávilaÁngel Encalada-Dávila
Ángel Encalada-Dávila
Samir EcheverriaSamir Echeverria
Samir Echeverria
Jordy Santana-VillamarJordy Santana-Villamar
Jordy Santana-Villamar
Gabriel Cedeño-CarpioGabriel Cedeño-Carpio
Gabriel Cedeño-Carpio
Mayken Espinoza-AndaluzMayken Espinoza-Andaluz
Mayken Espinoza-Andaluz
The development of green energy conversion devices has been promising to face climate change and global warming challenges over the last few years. Energy applications require a confident performance prediction, especially in polymer electrolyte fuel cell (PEFC), to guarantee optimal operation. Several researchers have employed optimization algorithms (OAs) to identify operating parameters to improve the PEFC performance. In the current study, several nature-based OAs have been performed to compute the optimal parameters used to describe the polarization curves in a PEFC. Different relative humidity (RH) values, one of the most influential variables on PEFC performance, have been considered. To develop this study, experimental data have been collected from a lab-scale fuel cell test system establishing different RH percentages, from 18 to 100%. OAs like neural network algorithm (NNA), improved grey-wolf optimizer (I-GWO), ant lion optimizer (ALO), bird swarm algorithm (BSA), and multi-verse optimization (MVO) were evaluated and compared using statistical parameters as training error and time. Results gave enough information to conclude that NNA had better performance and showed better results over other highlighted OAs. Finally, it was found that sparsity and noise are more present at lower relative humidity values. At low RH, a PEFC operates under critical conditions, affecting the fitting on OAs.