Stanislav A. Chupin

Dr. Stanislav A. Chupin

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2019 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
SCStanislav A. Chupin
Stanislav A. Chupin
VBVictor I. Bolobov
Victor I. Bolobov
This work presents results of experimental researches of influence of various high-temperature thermomechanical treatment (HTMT) modes in 35KhGSA steel – material applied in rock-destroying cutters – on hardness and wear rate for the most common abrasive rock in mining operations – sandstone. It has been found out that HTMT leads to increase of steel hardness and reduction of wear rate compared to heat treatment applied at manufacture of cutters. The maximal increase of hardness (by 23%) and reduction of wear rate (by 38%) corresponds to the mode of distortion accumulation of ~1,5 at 900 °С at water quenching and tempering at 230 °C. A conclusion that thermomechanical treatment is an effective way to increase the wear resistance of steels applied in the conditions of abrasion wear has been drawn.

29 October 2021 in Journal of Mining Institute
Verified
Journal Article
Open access
PDF file
AIAndrey Ivanov
Andrey Ivanov
YSYuriy D. Smirnov
Yuriy D. Smirnov
SCStanislav A. Chupin
Stanislav A. Chupin
Currently, the determination of the emission rate of suspended solids from a unit of the surface area of a man-made mass at various parameters of the wind flow is not sufficiently described. The analysis of the world experience of researchers shows that existing laboratory installations have various design features that do not allow to correctly determine the mass of the dust being flapped and wind-blown. Based on the analysis results, the concept of an innovative laboratory installation for the study of dust-forming surfaces has been developed. It takes into account the influence of wind shadows, the deturbulization of an artificially created air flow, the possibility of regulating not only the flow velocity mode, but also the creation of a vacuum or disturbance in the area of sample placement, as well as the formation of a certain angle of wind flow attack relative to the surface. The concept provides for the possibility of determining the volume of dust emissions by the values of the lost dust masses in the sample and by the values of dust concentrations in the outgoing stream. The calculation of the main basic elements of the installation using the ANSYS FLUENT software package was carried out. The model and configuration of the wind tunnel have been developed and calculated, the main geometric parameters and functional elements for the possibility of use in scientific work have been determined. For practical use of the empirical roughness value of the underlying surface, its values are recommended in a wide range – from zero for the water surface to 0.44 for large cities with tall buildings and skyscrapers. В настоящее время определение мощности выброса твердых взвешенных веществ с единицы площади поверхности техногенного массива при различных параметрах ветрового потока описано недостаточно. Анализ мирового опыта исследователей показал, что существующие лабораторные установки обладают различными конструктивными особенностями, не позволяющими корректно определить массу взметаемой и переносимой пыли. На основании результатов анализа разработана концепция инновационной лабораторной установки для исследования пылящих поверхностей. Она учитывает влияние аэродинамичеких теней, детурбулизацию искусственно создаваемого потока воздуха, возможность регулирования не только скоростного режима потока, но и создания разряжения или возмущения в области размещения образцов, а также формирования определенного угла атаки ветрового потока относительно поверхности. В концепции заложена возможность определения объемов выброса пыли по значениям потерянных масс пыли в образце и по значениям концентраций пыли в выходящем потоке. Проведен расчет основных базовых элементов установки с применением программного пакета ANSYS FLUENT. Разработана и рассчитана модель и компоновка аэродинамической трубы, определены основные геометрические параметры и функциональные элементы для возможности использования в научной работе. Для практического использования эмпирического показателя шероховатости подстилающей поверхности рекомендованы его значения в широких пределах – от нуля для водной поверхности до 0,44 для крупных городов с высокими зданиями и небоскребами.

31 May 2019 in Gornyi Zhurnal
Verified
Journal Article
Closed access
VBVictor I. Bolobov
Victor I. Bolobov
SCStanislav A. Chupin
Stanislav A. Chupin
VBV. S. Bochkov
V. S. Bochkov
IMI. I. Mishin
I. I. Mishin
The effect of high-temperature thermomechanical treatment (HTTT) on abrasive wear resistance of steel 30KHGGSA as the main material to manufacture holder of mining machine cutters is studied. The procedure of HTTT during deformation of cylindrical steel fragments at the preset settling-down rate and subsequent quenching is described. The finite element modeling in DEFORM-3 finds distribution of plastic strain in volume of forged pieces. On the plant based on the upright drilling machine, the abrasive wear resistance of forged pieces is tested on sandstone and siltstone as the medium-hardness and abrasivity co-rocks most frequently met in development heading. It is shown that pre-deformation of the fragments before quenching, i.e. HTTT, imporves the steel hardness from 44 to 55 HRC. It is shown that as against specimens nondeformed before quenching, the abrasive wear resistance of steel subjected to plastic straining up to εΣ ≈ 0.7 increases by 1.9 times in case of both siltstone and sandstone. Considering the obtained results, it is suggested to amend the manufacturing technology of cutters by quenching of fholder forging starting immediately from the forging temperature and by subjecting thereby the holder to high-temperature thermomechanical treatment. The cutting tool cartridge is to be held in the holder by cold pressing. It is assumed that HTTT application can essesntially (two times and more) improve wear resistance of steel holder head and, as a consequence, extend service life of cutters.

1 February 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
SCStanislav A. Chupin
Stanislav A. Chupin
VBVictor I. Bolobov
Victor I. Bolobov
The causes of failure of the tangential rotary cutter bits of the road header during stonedrift in rocks of medium strength are analyzed in the article. It was revealed that the most typical cause of failure of cutter bits is premature wear of the toolholder (body) of the cutter bit. It is well known that the most effective way to improve the wear resistance is to increase hardness. The influence of the thermomechanical treatment of the material of the cutter bit toolholder on its hardness is studied. It was established that the thermomechanical treatment of the cutter bit toolholder material results in the increase of its hardness. It was found that the increase of material hardness is proportional to the increase of material strain intensity during thermomechanical treatment. It was concluded that the use of thermomechanical treatment can lead to the increase of both the hardness and wear resistance of the cutter bit material.

1 July 2022 in Perpsectives of science and education
Verified
Journal Article
Closed access
SUSaint-Petersburg Mining University
Saint-Petersburg Mining University
AFAndrey I. Folomkin
Andrey I. Folomkin
SCStanislav A. Chupin
Stanislav A. Chupin
OTOlga Vasilevna Trybetskaya
Olga Vasilevna Trybetskaya
VSVeronika V. Sharok
Veronika V. Sharok
Introduction. For the last thirty years, UNESCO has been repeatedly raising questions of accessibility and quality of education for every child, teen, and adult by implementing the “Education for All” program. The new concept of education proposed by UNESCO aims at transforming people’s lives and formulates the following sustainable development goal “To provide inclusive and equitable quality education and create lifelong learning opportunities for all. One strategy for achieving this goal is to use and develop information and communication technology (ICT) to strengthen education systems, knowledge dissemination, access to information, and quality and effective learning. The aim of the work is to increase the efficiency of students’ learning of geometrical and graphic disciplines by developing a pilot electronic course in LMS Moodle and special software implementing elements of individualization of the learning process. Materials and methods. Theoretical research methods included generalization of scientific and pedagogical literature on formation of spatial thinking. Empirical research methods included testing, interviewing, and questioning using Google forms. Mathematical methods of research included algorithmizing and programming. Python 3.9 language and PyCharm development environment were used for writing the trainer program. The OpenCV, Matplotlib and Keras libraries, Microsoft PowerPoint, Microsoft Visio and CAD Compass-3D were used to create methodological materials Results. The software simulator for developing spatial thinking of engineering students studying “Descriptive Geometry” discipline has been developed in three versions. Conclusion. The ideas about the level of spatial thinking of modern students are supplemented. The original programs for the implementation of the elements of individualization of the educational process in the discipline of “Descriptive geometry” and algorithms of its work were developed and introduced into the scientific turnover, as well as the proposed pedagogical conditions of their use. Practical significance lies in the creation of learning and teaching methods and program basic elements for the use of end-to-end digital technology in the learning process.

1 November 2019 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
VBV I Bolobov
V I Bolobov
SCStanislav A. Chupin
Stanislav A. Chupin
The causes of failure of the bucket teeth of the excavator during excavations in rocks are analyzed in the article. It is shown that the most typical cause of failure of bucket teeth is wear of teeth. The wear with soft rocks (less than 1100 HV) which hardness is lower than the hardness of steel in the cold-work hardened state, a preliminary cold-work hardening can essentially (up to 10 times) increase the material wear resistance. The wear with rocks, having greater hardness with hardness of ~1250 HV, the cold-work hardening do not lead to increase of the Hadfield steel wear resistance.