BİLAL ÇOLAK

Dr. BİLAL ÇOLAK

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 March 2018 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
BÇBİLAL ÇOLAK
BİLAL ÇOLAK
NKNaci Kurgan
Naci Kurgan

1 September 2021 in Surface Topography: Metrology and Properties
Verified
Journal Article
Closed access
PDF file
BÇBİLAL ÇOLAK
BİLAL ÇOLAK
This study investigated the surface roughness characteristics of rolls textured using the Shot-Blast Texturing and Electro-Discharge Texturing methods. The rolling tests were carried out in an actual cold rolling mill tandem line, and the surface roughness transferred from the roughened rolls to the material with these two methods was examined. The study measured and compared the surface roughness of roughened rolls and the materials rolled by them. The study observed that the transfer ratio of electro-discharge texturing rolls was higher, but the transfer ratio of SBT rolls increased towards the end of the rolling campaign. The study also examined the extent to which the surface roughness of the rolls changed after rolling. Therefore, the level of reduction and how much was preserved were determined by comparing the surface roughness of the rolls before and after the rolling campaign. Shot-blast texturing rolls were found to have lost 53% of their roughness while electro-discharge texturing rolls lost only 33%.

15 September 2023 in Karadeniz Fen Bilimleri Dergisi
Verified
Journal Article
Open access
PDF file
BÇBİLAL ÇOLAK
BİLAL ÇOLAK
ZAZahoor Ahmed
Zahoor Ahmed
BÖBatuhan Özakın
Batuhan Özakın
NKNaci Kurgan
Naci Kurgan
This study investigated the effect of rolling parameters such as speed, thickness reduction, roll surface roughness, material thickness, surface condition (dry or lubricated), and rolling force on the roughening characterization in asymmetrical rolling. The surface roughness of the samples subjected to rolling tests was measured. The roughness values' average and standard deviation were found, and 3-D scanning images were acquired. Lubricated texturing experiments revealed that lubrication reduced roughness transfer. It was found that the introduction of roughness on the material surface decreased as the rolling speed increased. On the other hand, a higher speed increases the rolling force, which increases the surface roughness. The effect of speed on the standard deviation varies in direct proportion. Furthermore, lubricated rolling produced a more homogenous roughness distribution at higher speeds, while dry rolling produced homogeneous roughness at lower speeds. It was revealed that the rolling force is higher with thicker materials. While the roll roughness did not affect the rolling force using thicker material much, this effect was more pronounced in the very rough roll using thinner material. The standard deviation was lower in smaller reduction ratios using rough and very rough rolls. According to the results, although asymmetrical rolling has some advantages compared to conventional rolling, it was concluded that it is not a suitable method for roughening steel strips.

13 June 2021 in Ironmaking & Steelmaking: Processes, Products and Applications
Verified
Journal Article
Closed access
BÇBİLAL ÇOLAK
BİLAL ÇOLAK
When producing cold-rolled steel sheets, the penultimate annealing process is followed by a final skin-pass rolling (or temper rolling) whose purpose is to eliminate any discontinuous yielding which creates stretcher–strain markings when the steel sheets are formed. To find out the critical reduction ratio eliminating the discontinuous yield phenomenon, the samples were annealed at 820°C for 3 min and then subjected to the temper rolling at various thickness reductions at room temperature. Results showed that the discontinuous yield phenomenon could not be eliminated in the case of a thickness reduction less than 0.5%, that a certain reduction ratio should be exceeded to eliminate the discontinuous yielding, and that the aging time varied depending on the reduction ratio. In addition, while the low-carbon steels did not undergo strain aging in three months with a 1% thickness reduction, they underwent strain aging in at least four months with higher thickness reductions.

9 October 2023 in Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Verified
Journal Article
Open access
PDF file
BÇBİLAL ÇOLAK
BİLAL ÇOLAK
Materials with compressive stresses on the surface withstand fatigue failures, cracking, galling, and corrosion. This compressive stress at the surface can be created by temper rolling. The rolling process must be conducted with an appropriate reduction to obtain the desired benefit from temper rolling. A 1% thickness reduction is usually applied to endow flatness and surface texture to the strip, and this reduction is sufficient to eliminate the discontinuous yielding phenomenon. In this study, 2.5-mm-thick low-carbon steel sheet (DC01 grade) samples were annealed at approximately 600°C for 5 minutes, temper-rolled at room temperature at various reduction ratios subsequently, and the residual stresses formed along the thickness by rolling were investigated. This study has revealed that a 1% reduction ratio is insufficient for developing compressive stresses on the surface, but this can only be achieved with a 1.5% reduction ratio. When the reduction ratio was increased to 1.8%, tensile stresses began to occur inside, along with compressive stresses on the surface. It was observed that at a reduction ratio of 2%, the situation was reversed again; tensile stresses began to regenerate at the surface, and this became more pronounced up to a 10% reduction ratio.

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
SHShahad H. Hasan
Shahad H. Hasan
BÇBİLAL ÇOLAK
BİLAL ÇOLAK
SAShukry H. Aghdeab
Shukry H. Aghdeab
The purpose of this research is to investigate the influence of input parameters (current, pulse on, pulse off) on materials eviction rate (MRR) when cutting CK The purpose of this research is to investigate the influence of input parameters (current, pulse on, pulse off) on materials eviction rate (MRR) when cutting CK