Mechanical properties of semiconductors: CdTe, ZnTe and CdTe alloyed with 2% and 5 at% of Zn have been calculated, using the computer code WIEN2k. The program uses the Density Functional Theory. The results show that increasing the amount of Zn, results in greater values of mechanical properties and contraction of the lattice parameter since replacement of Cd by Zn establish lower Zn-Te distance compared with Cd-Te. The behavior is different for the C12 constant of Cd0.90Zn0.10Te, the shear and Young modulus of CdTe. While Poisson's ratio is constant. The calculated values for CdTe and ZnTe differ from the experimental values between 8% and 21%. The calculated values differ from others authors between 2% and 21%. There are no experimental data of the alloyed CdTe. Values of CdTe alloyed whit Zn are between the CdTe and ZnTe closest to the CdTe. Differences with data calculated by other authors are noticeable.
Cd1−xZnxTe (0 ≤ x ≤ 0.1) ingots were obtained by Bridgman’s method using two different speeds in order to find the optimal conditions for single-crystalline growth. Crystalline quality was studied by chemical etching, the elemental composition by wavelength dispersive spectroscopy (WDS), tellurium (Te) precipitates/inclusions concentration by differential scanning calorimetry (DSC), optical transmission by Fourier transformed infrared spectrometry (FTIR), and band gap energy (Egap) by photoluminescence (PL). It was observed that the ingots grown at a lower speed were those of the best crystalline quality, having at most three grains of different crystallographic orientation. The average dislocations density in all of them were similar and correspond to materials of good quality. EPMA results indicated that the homogeneity in the composition was excellent in the ingots central part. The concentration of Te precipitates/inclusions in all ingots was below the instrument (DSC) detection limit, 0.25% wt/wt. In the case of wafers from Cd0.96Zn0.04Te and Cd0.90Zn0.10Te ingots, the optical transmission was better than that of commercial materials and varied between 60% and 70%, while for pure CdTe, the transmission range was between 50% and 55%, the latter being decreased by the presence of Te precipitates/inclusions. The band gap energy Eg of different wafers was experimentally obtained by PL measurements at 76 K. We observed that Eg increased with the Zn concentration of the wafers, following a linear regression comparable to those proposed in the literature, and consistent with the results obtained with other techniques.
Cadmium selenide is a II-VI semiconductor compound with 1.67 eV energy gap (≈ 300 K) and high stopping power for nuclear radiation. Its crystalline structure is hexagonal (wurtzite) and it is used in solar cells, transistors, light emitting diodes, electroluminescent devices, nuclear radiation detectors at room temperature and nonlinear optical devices [Shan et al. (1994), Young et al. (1994), Van Calster et al. (1988), Chopra (1969), Bhargava (1997)]. It is also employed as substrate for epitaxial growth of HgCdSe [Korostelin et al. (1996)]. Qualities of devices are critically dependent on their material properties. Crystalline characterization of a CdSe commercial wafer was our main goal. The crystalline quality was evaluated by different techniques. Since it is used as an optical window in the IR spectrum, its optical transmittance was measured by FTIR (Perkin-Elmer System 2000). The etch pits distribution was determined by chemical etching. Dislocation density was obtained by counting on optical micrographs (Union Versamet 5279) meanwhile misorientation between adjacent subgrains by means of Shockley - Read approximation. The reliability of the techniques used in determining the crystalline quality was evaluated. The etching solution was sensitive in linear defects detection and crystalline quality was adequate for devices manufacture of this material. Transmission electron microscopy employment confirmed these result.
Cd1-xZnxTe (0 <= x <= 1) and ZnTe are II-VI semiconductors, which are used in single crystalline structure to improve their crystalline and electrical properties. The CZT and ZnTe must possess high crystalline and electrical quality to be used, the first in x or gamma-ray detectors, and as substrates for suitable epitaxial films for detecting IR radiation and the second for the manufacture of laser diodes and high intensity light emitters, both cases in the green wavelengths. In this work CZT was synthesized by the Bridgman method employing a temperature gradient of 10 degrees C/cm at speeds of 1.66 mm/h and 3.22 mm/h for different Zn concentrations. Meanwhile ZnTe was synthesized by physical vapor transport employing a temperature gradient of 6 degrees C/cm at a speed of 6 mm/day. Chemical etching and low and high transmission electron microscopy (LRTEM and HRTEM) were employed to determine the crystalline quality of all materials. It was observed that CZT ingots had an average dislocations density similar in all ingots grown in both speeds and all concentrations while the ZnTe showed a lower dislocation density. HRTEM micrographs showed in all semiconductors an important structural order. These characteristics showed that the crystalline quality of CZT and ZnTe was suitable for manufacturing optoelectronic devices. Furthermore, Electrical Conductivity, Thermal Diffusivity, Specific Heat and Seebeck Coefficient were measured as temperature function in all these materials. The influence of structural properties in physical properties was analyzed in order to determine the relationship with the observed crystal defects.
CdSe is II-VI semiconductor with compact hexagonal structure. It has a band gap of 1.82 eV and a high stopping power for nuclear radiation. Single crystalline CdSe ingots were grown by Physical Vapor Transport (PVT) employing a horizontal reactor. As devices critically depend on material properties its single crystalline quality was determined by chemical etching and transmission electron microscopy. Results were compared to those corresponding to Bridgman High Pressure (HPB) grown material and also to PVT material grown in a vertical reactor.