Hala Aljawhari

Prof. Hala Aljawhari

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 April 2023 in ACS Nano
Verified
Journal Article
Open access
TGTianchao Guo
Tianchao Guo
XXXiangming Xu
Xiangming Xu
CLChen Liu
Chen Liu
YWYizhou Wang
Yizhou Wang
YLYongjiu Lei
Yongjiu Lei
HAHusam N. Alshareef
Husam N. Alshareef
Direct MXene deposition on large-area 2D semiconductor surfaces can provide design versatility for the fabrication of MXene-based electronic devices (MXetronics). However, it is challenging to deposit highly uniform wafer-scale hydrophilic MXene films (e.g., Ti3C2Tx) on hydrophobic 2D semiconductor channel materials (e.g., MoS2). Here, we demonstrate a modified drop-casting (MDC) process for the deposition of MXene on MoS2 without any pretreatment, which typically degrades the quality of either MXene or MoS2. Different from the traditional drop-casting method, which usually forms rough and thick films at the micrometer scale, our MDC method can form an ultrathin Ti3C2Tx film (ca. 10 nm) based on a MXene-introduced MoS2 surface polarization phenomenon. In addition, our MDC process does not require any pretreatment, unlike MXene spray-coating that usually requires a hydrophilic pretreatment of the substrate surface before deposition. This process offers a significant advantage for Ti3C2Tx film deposition on UV-ozone- or O2-plasma-sensitive surfaces. Using the MDC process, we fabricated wafer-scale n-type Ti3C2Tx-MoS2 van der Waals heterojunction transistors, achieving an average effective electron mobility of ∼40 cm2·V-1·s-1, on/off current ratios exceeding 104, and subthreshold swings of under 200 mV·dec-1. The proposed MDC process can considerably enhance the applications of MXenes, especially the design of MXene/semiconductor nanoelectronics.

1 February 2022 in Nano-Structures & Nano-Objects
Verified
Journal Article
Closed access
HAHala Aljawhari
Hala Aljawhari
HBHanan Bin-Thiyab
Hanan Bin-Thiyab
NENihal Elbialy
Nihal Elbialy

6 December 2013 in Advanced Materials Research
Verified
Journal Article
Closed access
PDF file
HAHala Aljawhari
Hala Aljawhari
JCJ.A. Caraveo-Frescsa
J.A. Caraveo-Frescsa
Single-phase Cu2O films with p-type semiconducting properties were successfully deposited by reactive DC magnetron sputtering at room temperature followed by post annealing process at 200°C. Subsequently, such films were used to fabricate bottom gate p-channel Cu2O thin film transistors (TFTs). The effect of using high-κ SrTiO3 (STO) as a gate dielectric on the Cu2O TFT performance was investigated. The results were then compared to our baseline process which uses a 220 nm aluminum titanium oxide (ATO) dielectric deposited on a glass substrate coated with a 200 nm indium tin oxide (ITO) gate electrode. We found that with a 150 nm thick STO, the Cu2O TFTs exhibited a p-type behavior with a field-effect mobility of 0.54 cm2.V-1.s-1, an on/off ratio of around 44, threshold voltage equaling-0.62 V and a sub threshold swing of 1.64 V/dec. These values were obtained at a low operating voltage of-2V. The advantages of using STO as a gate dielectric relative to ATO are discussed.

1 June 2021 in Materials Research Bulletin
Verified
Journal Article
Closed access
HBHend Badahdah
Hend Badahdah
AKArwa Kutbee
Arwa Kutbee
DKDina Katowah
Dina Katowah
Mahmoud A. HusseinMahmoud A. Hussein
Mahmoud A. Hussein
NANoorah Al-Ahmadi
Noorah Al-Ahmadi
HAHala Aljawhari
Hala Aljawhari

20 September 2022 in Crystals
Verified
Journal Article
Open access
PDF file
HAHala Aljawhari
Hala Aljawhari
Nuha A. AlhebshiNuha A. Alhebshi
Nuha A. Alhebshi
In this work, we introduce an environmental and sustainable approach to grow free standing heterogeneous Cu2O-Cu(OH)2 nanocomposites on a Cu mesh using spinach leaf extract and glycerol. Structural characterizations for samples annealed at 200 °C revealed that there is more Cu(OH)2 than Cu2O on the mesh surface. The photocatalytic activity of the green synthesized catalyst was studied for degradation of a cationic dye methylene blue (MB), an anionic dye methyl orange (MO) and a mixture of both dyes. The effect of changing the dye’s initial pH value on the photodegradation process was explored. After 40 min of irradiation under sunlight, with a maximum intensity of 5 mW/cm2, a basic MB dye (pH-11) showed about 80% color removal with an average kinetic rate of 94.5 m·min−1. In contrast, 93% of the acidified MO dye (pH-2) was degraded with an average kinetic rate of 126.5 m·min−1. Moreover, the versatility of the Cu2O-Cu(OH)2@Cu mesh was evaluated using a remarkable selective separability for a mixture of MB and MO at pH = 2, in the dark and under normal sunlight. Such promising outcomes indicate the potential of our green composites to degrade dyes as both photocatalysts under daylight and as Fenton-like catalysts in darkness.

22 December 2021 in Advanced Electronic Materials
Verified
Journal Article
Closed access
PDF file
HAHala Aljawhari
Hala Aljawhari