Industry 4.0 in healthcare involves use of a wide range of modern technologies including digitisation, artificial intelligence, user response data (ergonomics), human psychology, the Internet of Things, machine learning, big data mining, and augmented reality to name a few. The healthcare industry is undergoing a paradigm shift thanks to Industry 4.0, which provides better user comfort through proactive intervention in early detection and treatment of various diseases. The sector is now ready to make its next move towards Industry 5.0, but certain aspects that motivated this review paper need further consideration. As a fruitful outcome of this review, we surveyed modern trends in this arena of research and summarised the intricacies of new features to guide and prepare the sector for an Industry 5.0-ready healthcare system.

Titanium alloys based on orthorhombic titanium aluminide Ti₂AlNb are promising refractory materials for aircraft engine parts in the operating temperature range from 600–700 °C. Parts made of Ti₂AlNb-based alloys by traditional technologies, such as casting and metal forming, have not yet found wide application due to the sensitivity of processability and mechanical properties in chemical composition and microstructure compared with commercial solid-solution-based titanium alloys. In the last three decades, metal additive manufacturing (MAM) has attracted the attention of scientists and engineers for the production of intermetallic alloys based on Ti₂AlNb. This review summarizes the recent achievements in the production of O-phase-based Ti alloys using MAM, including the analysis of the feedstock materials, technological processes, machines, microstructure, phase composition and mechanical properties. Powder bed fusion (PBF) and direct energy deposition (DED) are the most widely employed MAM processes to produce O-phase alloys. MAM provides fully dense, fine-grained material with a superior combination of mechanical properties at room temperature. Further research on MAM for the production of critical parts made of Ti₂AlNb-based alloys can be focused on a detailed study of the influence of post-processing and chemical composition on the formation of the structure and mechanical properties, including cyclic loading, fracture toughness, and creep resistance.

The research demonstrates microstructural changes and development of specific texture in Ti-6Al-4V specimens produced by electron beam melting (EBM) under different conditions. The effect of two factors, namely, raw material (powder) recycling and hot isostatic pressing (HIP), on the EBM produced samples structure and properties, has been explored. The as-printed and treated samples were investigated using electron backscattered diffraction (EBSD) analysis. Modification of mechanical properties after the EBM and HIP are explained by the EBSD data on microstructural phenomena and phase transformations. The work is devoted to assessing the possibility of reusing the residual titanium alloy powder for the manufacture of titanium components by the combination of EBM and HIP methods.

Many current-generation biomedical implants are fabricated from the Ti-6Al-4V alloy because it has many attractive properties, such as low density and biocompatibility. However, the elastic modulus of this alloy is much larger than that of the surrounding bone, leading to bone resorption and, eventually, implant failure. In the present study, we synthesized and performed a detailed analysis of a novel low elastic modulus Ti-based alloy (Ti-28Nb-5Zr-2Ta-2Sn (TNZTS alloy)) using a variety of methods, including scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and tensile test. Additionally, the in vitro biocompatibility of the TNZTS alloy was evaluated using SCP-1, SaOs-2, and THP-1 cell lines and primary human osteoblasts. Compared to Ti-6Al-4V, the elastic modulus of TNZTS alloy was significantly lower, while measures of its in vitro biocompatibility are comparable. O₂ plasma treatment of the surface of the alloy significantly increased its hydrophilicity and, hence, its in vitro biocompatibility. TNZTS alloy specimens did not induce the release of cytokines by macrophages, indicating that such scaffolds would not trigger inflammatory responses. The present results suggest that the TNZTS alloy may have potential as an alternative to Ti-6Al-4V.

Thermo-mechanical controlled processing (TMCP) is employed to obtain the required level of mechanical properties of contemporary HSLA steel plates utilized for gas and oil pipeline production. The strength and crack resistance of pipeline steels are mainly determined by its microstructure and crystallographic texture. In this study, the influence of the structural and textural states of industrially produced API-5L X70-X80 pipeline steels on tensile mechanical properties was analyzed. TMCP routes with different hot rolling temperatures and cooling rates were employed. The texture of steel was assessed using the Taylor factor, which was calculated based on electron backscatter diffraction (EBSD). The decrease in rolling temperature resulted in the sharper texture characterized by {001} planes banding (cleavage planes in the bcc lattice) parallel to rolling direction. The tensile deformation behavior at the stage of necking was determined by the crystallographic and morphological texture of the material and demonstrated significant anisotropy. Rupture of all investigated samples was accompanied by the development of splitting on the fracture surface. The splitting was localized in the rolling plane similar to the splitting in standard Charpy tests of pipeline steels.

X-ray diffraction analysis and transmission and scanning electron microscopy have been used to study regularities of the formation of structure and phase composition of a VT16 alloy during its quenching. The formation of an athermal ω phase in the VT16 alloy with the initial (α + β) structure during quenching of the alloy from 800°C was found to be possible. Quenching temperatures (T _q) at which various metastable phase compositions, such as the metastable β solid solution, β + α″ + ω, β + α″, and α″ martensite, are formed have been determined to be 750, 800, 750–850, and ≤850°C, respectively. Dependences of variations in the volume fractions of phases were plotted. It has been shown that, at quenching temperatures close to the β-transus, the active growth of β-phase grains takes place at the expense of a decrease in the α-phase volume fraction.