In nanolubrication, friction-reduction and anti-wear behaviors are dependent on the characteristics of nanoparticles, such as size, shape, and concentration. Some mechanisms of friction-reduction and anti-wear of NNP in lubricant have been reported as protective film, rolling effect, polishing or smoothing effect, mending effect, and the third body. Thus, this work studied differences in nanolubrication mechanism as functions of size and concentration of CuO NNP added in synthetic oil. Three levels of concentration and size were evaluated: 0.1, 0.25, and 0.5 % wt., and 2.5, 4.4, and 8.7 nm, respectively. The methodology was divided into three steps: first, the preparation of CuO NNP from an alcohol-thermal method. These were characterized by XRD (X-ray diffraction) and TEM (Transmission electron microscopy). The second part was constituted by evaluation of lubricant with NNP by a tribological test, which was carried out under boundary lubrication conditions in high frequency reciprocating rig (HFRR) equipment. The last step was the characterization of the wear mechanism; scanning electron microscopy (SEM) and Raman spectroscopy aided to identify tribochemistry interactions between nanolubricant and steel surface. The results showed that the concentration of NNP influenced wear: low concentration decreased the wear and promoted a smooth surface, while more plastic deformation was observed in high concentration. For the NNP size, the smallest size corresponded to the lowest friction coefficient. The best results were obtained for nanolubricant with a concentration of 0.1 % wt. and a NNP size of 2.5 nm.
Additives are essential in lubricant development, improving their performance by the formation of a protective film, thus reducing friction and wear. Some such additives are extreme pressure additives. However, due to environmental issues, their use has been questioned because their composition includes sulfur, chlorine, and phosphorus. Nanoparticles have been demonstrated to be a suitable substitute for those additives. This paper aims to make a comparison of the tribological performance of conventional EP additives and oxides nanoparticles (copper and zinc) under boundary lubrication conditions. The additives (nanoparticles, ZDDP, and sulfur) were added to mineral and synthetic oils. The lubricant tribological properties were analyzed in the tribometer HFRR (high frequency reciprocating rig), and during the test, the friction coefficient and percentual of film formation were measured. The wear was analyzed by scanning electron microscopy. The results showed that the conventional EP additives have a good performance owing to their anti-wear and small friction coefficient in both lubricant bases. The oxides nanoparticles, when used as additives, can reduce the friction more effectively than conventional additives, and displayed similar behavior to the extreme pressure additives. Thus, the oxide nanoparticles are more environmentally suitable, and they can replace EP additives adapting the lubricant to current environmental requirements.
1 June 2011 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Compacted Graphite Iron (CGI) is a good option for the manufacturing of engine blocks, because of the possibilities to decrease the wall thickness and to operate at higher pressures. However, due to its greater tensile strength and hardness compared with grey cast iron, the pearlitic CGI structure makes its machining more difficult. Thus, the aim of this paper is to investigate the improvements in CGI drilling achieved through the use of cutting fluids with EP additives. Experimental investigation of the influence of an EP additive on the drilling process was carried out using a CNC machine with 7.64 kW of power and maximum rotation of 5000 rpm. The cutting parameters were a cutting speed of 110 m/min, feed velocity of 350 mm/min and hole-depth of 20 mm. Three cutting fluids were analyzed, with and without EP additives. The results showed that the EP additive influenced the CGI drilling performance due to a layer comprised of sulphur (EP additive) and metal. Adhesion was avoided and the friction and wear behavior was improved
The purpose of this work was to study the influence of soybean biodiesel addition in ultra-low sulfur diesel (ULSD) on its tribological behavior under low-amplitude reciprocating conditions, simulating the operation of a fuel injector system. The methodology was divided into three parts: the first was the fuel preparation and its physicochemical characterization, where were studied four fuels (diesel, soybean biodiesel, and mixtures of them).The following step was the evaluation of the fuel tribological properties, using the high-frequency reciprocating rig (HFRR) test. These tests were carried out by steel ball-on-disk lubricated contact, on which the friction coefficient of friction (COF), the film percentage, and the wear scar diameter (WSD) were measured, according to ASTM D6079-11. In the end, the analysis of the damages presented on the worn disk surfaces was characterized by scanning electronic microscopy (SEM) and atomic force microscopy (AFM) techniques. Results showed that the addition of biodiesel to ULSD is an excellent option to restore the lubricating ability of this fuel. The biodiesel incorporation reduces the friction coefficient and improves the film formation. Besides, the evaluation of worn disk surfaces using SEM and AFM techniques showed that biodiesel avoids damages to surface through protective film formation and reduces the superficial roughness.