Biodiesel is considered as a key prospective renewable energy source in India. Hence, a study was carried out for the improvement of palm kernel oil biodiesel production using a transesterification process at different molar ratios. This study comprehensively examined all aspects of biodiesel from optimum production to the effect of additives on its combustion behavior. The optimum yield condition was validated with the MINITAB-17 software and analyzed using the Taguchi method. Two different additives, 5% diethyl ether (DEE) and 2000 ppm Butylated hydroxyltoluene (BHT), were also experimented. Engine experiments were conducted at constant speed (1500 rpm) and five different engine loads (0, 25, 50, 75 and 100%) on a single-cylinder direct injection diesel engine. Heat release rate, brake specific fuel consumption, brake thermal efficiency, engine emissions, such as CO, HC, NOx, and smoke opacity were analyzed. The maximum palm kernel oil (PKO) biodiesel yields, obtained at 55 °C, for the KOH and NaOH catalysts were 86.69% and 75.21% at the molar ratio of 6:1. B20BHT combustion showed 4.6% higher brake thermal efficiency (BTE). NOx emission was reduced by 19.4%, compared to the diesel fuel values. DEE resulted in higher CO and HC emissions compared to diesel fuel values by 39.2% and 7.6%, respectively, whereas smoke emission was improved by 11.5%.
1 January 2025 in International Journal of Energy Research
The use of biodiesel is becoming inevitable due to the depletion of fossil fuel resources. Biodiesel is an attractive alternative fuel derived from natural oils and can be used directly in diesel engines with no major change. However, various biodiesels may exhibit different performance behaviors and emission characteristics, with some performing worse than diesel fuel. The present research work investigates the performance, combustion, and emission behavior of rubber seed biodiesel (RSB)/diesel blends (B20, B30, B40) and B20 + ethyl hexyl nitrate (EHN) at four injection timings (19°, 21°, 25°, and 27° before top dead center [BTDC]) in a single‐cylinder DI diesel engine. Combustion of biodiesel/diesel blends generally resulted in worse performance, except smoke emission. The addition of EHN reduced hydrocarbon (HC) emissions but negatively impacted brake‐specific fuel consumption (BSFC) and brake thermal efficiency (BTE). However, advanced injection timing not only restored the combustion parameters to the B20 level but also brought them closer to those of the diesel engine. Advancing the injection timing to 27° BTDC improved BSFC and BTE by 3% and 4% compared to B20, respectively. Additionally, the HC emission decreased strongly by 80% and 73%, and smoke emission decreased by 15% and 16%, respectively, compared to B20 and diesel fuel values. A slight improvement in NO x emissions (by 2%) was also observed compared to B20. An increase in cylinder pressure from 66.2 to 67.4 bar was observed with advanced injection timing, contributing to improved engine performance. Analysing of combustion characteristics showed that RSB/diesel blends, when doped with EHN, offer better performance at advanced injection timings making them a suitable alternative fuel to replace diesel fuel usage in developing countries like India.
Biodiesel is currently utilised as an alternative to conventional fuels. However, blends only up to a particular ratio improve the engine performance and fuel filterability. Higher biodiesel concentrations may cause diesel fuel filter clogging. The influence of blends of Ceiba pentandra (kapok) biodiesel (B0–B100 in 20% increments) on fuel filter blocking tendency, pressure drop, and soaking strength was investigated through filter media analysis. Fuel filter performance was similar to diesel up to B20, but higher blends had a detrimental effect. As per the filterability results, B20 was selected for further evaluation. Injection timing (IT) of fuel was the most influential parameter on the performance, combustion, and emission behaviour of diesel engines. This work aims to improve engine performance and emissions by altering IT from 21° before top dead centre (BTDC) to 27° BTDC with Ceiba pentandra biodiesel (B20), and results are compared with diesel at IT of 23° BTDC. Advanced IT (27° BTDC) caused lower brake specific fuel consumption (20%) and higher brake thermal efficiency (13%), and we observed low HC and smoke emissions at all advanced ITs. A reduction by 23.5% and 7.5% in hydrocarbon and smoke, respectively, was seen at 27° BTDC.
Biodiesels are widely recognized as a leading choice among the alternative options to traditional petrodiesel fuel due to their significant technical and e
The broad applications of IC engines hasten the evolution of our civilization and society. In this research, the biodiesel is derived from cottonseed oil through trans-esterification process and various diesel blends with fuel additive (n-butanol) were prepared and tested in single cylinder and four stroke diesel engine. The results for blend B20 showed 11% higher SFC than diesel. Use of BN20 as a fuel helped a decrease by 3.45% with B20. There was a 5.58% rise in the BTE of BN20 compared to B20 at medium operating conditions. Carbon monoxide (CO) emission of B20 was 33% lower than diesel and BN20 blend 16.7% lower than B20. A hydrocarbon (HC) emission from pure biodiesel (B100) resulted in a 10.5% reduction compared to diesel while the increase with respect to BN20 was 13.6%. The NOx emission for B20 and B100 were 7.4% and 16% increases compared to diesel respectively. The NOx value decreases with addition of n- butanol to B20 was 2.4% compared to B20. It was observed that the CSOME with n-butanol a good choice of fuel in terms of performance and improved emissions than diesel and would be a better substitute fuel for a diesel engine.
2 February 2024 in International Journal of Automotive Technology