Łukasz Stala

Mr. Łukasz Stala

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2021 in Water Research
Verified
Journal Article
Closed access
ŁSŁukasz Stala
Łukasz Stala
JUJustyna Ulatowska
Justyna Ulatowska
IPIzabela Polowczyk
Izabela Polowczyk

Verified
Journal Article
Open access
PDF file
JUJustyna Ulatowska
Justyna Ulatowska
ŁSŁukasz Stala
Łukasz Stala
IPIzabela Polowczyk
Izabela Polowczyk
Good sorption properties and simple synthesis route make schwertmannite an increasingly popular adsorbent. In this work, the adsorption properties of synthetic schwertmannite towards Cr(VI) were investigated. This study aimed to compare the properties and sorption performance of adsorbents obtained by two methods: Fe3+ hydrolysis (SCHA) and Fe2+ oxidation (SCHB). To characterise the sorbents before and after Cr(VI) adsorption, specific surface area, particle size distribution, density, and zeta potential were determined. Additionally, optical micrographs, SEM, and FTIR analyses were performed. Adsorption experiments were performed in varying process conditions: pH, adsorbent dosage, contact time, and initial concentration. Adsorption isotherms were fitted by Freundlich, Langmuir, and Temkin models. Pseudo-first-order, pseudo-second-order, intraparticle diffusion, and liquid film diffusion models were used to fit the kinetics data. Linear regression was used to estimate the parameters of isotherm and kinetic models. The maximum adsorption capacity resulting from the fitted Langmuir isotherm is 42.97 and 17.54 mg·g−1 for SCHA and SCHB. Results show that the adsorption kinetics follows the pseudo-second-order kinetic model. Both iron-based adsorbents are suitable for removing Cr(VI) ions from aqueous solutions. Characterisation of the adsorbents after adsorption suggests that Cr(VI) adsorption can be mainly attributed to ion exchange with SO42− groups.

4 May 2022 in Journal of Hazardous Materials
Verified
Journal Article
Open access
ŁSŁukasz Stala
Łukasz Stala
JUJustyna Ulatowska
Justyna Ulatowska
IPIzabela Polowczyk
Izabela Polowczyk
The amino-hypophosphite polyampholyte (AHP) obtained from cheap and safe building blocks lacks a typical ion-scavenger matrix derived from crude-oil intermediates like poly(divinylbenzene), which is an advantage to commercial solutions. AHP is characterised by sorption capacity comparable to some ion scavengers available on the market, as it was found that its maximum capacity in the temperature range from 298 K to 328 K varies between 114 and 146 mg Cu(II) g-1 of dry AHP. The possible application of the AHP in the Cu(II) removal process from galvanic effluent was investigated. The results show that it is possible to achieve a good removal rate for model wastewater. The inlet Cu2+ concentrations of model wastewater were 6.4 mg Cu(II) dm-3 and 36,2 mg Cu(II) dm-3, acidic and basic galvanic wastewater respectively. After the removal process concentrations were lowered to 1.3 mg Cu(II) dm-3 and 5.1 mg Cu(II) dm-3, for acidic and basic galvanic wastewater respectively. It was found that the presence of Ca(II) and Na(I) did not significantly influence the Cu(II) removal process. The obtained results indicate that the prepared more environmentally safe ion scavenger can be applicable in a wide range of metal ion removal processes.

1 September 2020 in Physicochemical Problems of Mineral Processing
Verified
Journal Article
Closed access
JUJustyna Ulatowska
Justyna Ulatowska
ŁSŁukasz Stala
Łukasz Stala
ANAlicja Nowakowska
Alicja Nowakowska
IPIzabela Polowczyk
Izabela Polowczyk

8 September 2023 in RSC Advances
Verified
Journal Article
Open access
PDF file
JUJustyna Ulatowska
Justyna Ulatowska
ŁSŁukasz Stala
Łukasz Stala
NTNatasza TrzęSowska
Natasza TrzęSowska
IPIzabela Polowczyk
Izabela Polowczyk
This study investigated the sorption of Ni(II) ions from an aqueous solution using novel, synthetic amino-hypophosphite polyampholyte resin (AHP) in a batch adsorption system. The removal of Ni(II) ions was determined as a function of pH (2.0–8.0), initial concentration of Ni(II) ions (2.0–20.0 mM), resin dosage (1.0–10.0 g dm−3), contact time (0.04–24 h), and temperature (298–318 K). Moreover, continuous fixed-bed column sorption was also studied using model solutions and actual wastewater from the galvanising plant. The batch sorption experimental data showed that the maximum pH for efficient Ni(II) ion removal was about 5.0. An equilibrium was reached after about 24 hours. The kinetics results were fitted using pseudo-first-order (PFO), pseudo-second-order (PSO), liquid film (LFD), and intraparticle diffusion (IPD) models. Freundlich and Langmuir isotherm models were applied for sorption equilibrium data. The maximum sorption capacity was obtained from the Langmuir equation to be 2.39, 2.52, and 2.62 mmol g−1 at 298, 308, and 318 K, respectively. The thermodynamic parameters for the sorption of Ni(II) ions on AHP imply the endothermic and spontaneous character of the process. The experimental results demonstrated that amino-hypophosphite polyampholyte resin could be used to effectively remove Ni(II) ions from model solutions and real wastewater.

4 February 2019 in EPJ Web of Conferences
Verified
Journal Article
Open access
ŁSŁukasz Stala
Łukasz Stala
KTKrzysztof Tomczuk
Krzysztof Tomczuk
The paper presents two methods of determining calibration curve of a new device for blood pressure measurement. The device was developed at Wrocław University of Science and Technology. First method is based on parallel measurement of systolic and diastolic pressure measurement with use of reference device such as sphygmomanometer and researched new device with pneumatic sensor equipped with voltage type output. Obtained data (systolic ps and diastolic pd pressure, maximum us and minimum ud voltage) was then used to determine individual pressure-voltage characteristic of the device, which can be represented as a linear equation. Second method is based on substitution of experimentally proved coefficient b with its analytical equivalent extracted from mathematical model of described pneumatic sensor. Described methods were verified experimentally and compared. Metrological parameters of the device were designated.