Jae Phil Park

Mr. Jae Phil Park

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 December 2016 in Materials
Verified
Journal Article
Open access
PDF file
JPJae Phil Park
Jae Phil Park
Chanseok ParkChanseok Park
Chanseok Park
JCJongweon Cho
Jongweon Cho
CBChi Bum Bahn
Chi Bum Bahn
It is extremely difficult to predict the initiation time of cracking due to a large time spread in most cracking experiments. Thus, probabilistic models, such as the Weibull distribution, are usually employed to model the initiation time of cracking. Therefore, the parameters of the Weibull distribution are estimated from data collected from a cracking test. However, although the development of a reliable cracking model under ideal experimental conditions (e.g., a large number of specimens and narrow censoring intervals) could be achieved in principle, it is not straightforward to quantitatively assess the effects of the ideal experimental conditions on model estimation uncertainty. The present study investigated the effects of key experimental conditions, including the time-dependent effect of the censoring interval length, on the estimation uncertainties of the Weibull parameters through Monte Carlo simulations. The simulation results provided quantified estimation uncertainties of Weibull parameters in various cracking test conditions. Hence, it is expected that the results of this study can offer some insight for experimenters developing a probabilistic crack initiation model by performing experiments.

27 June 2016 in Materials
Verified
Journal Article
Open access
PDF file
JPJae Phil Park
Jae Phil Park
CBChi Bum Bahn
Chi Bum Bahn
The typical experimental procedure for testing stress corrosion cracking initiation involves an interval-censored reliability test. Based on these test results, the parameters of a Weibull distribution, which is a widely accepted crack initiation model, can be estimated using maximum likelihood estimation or median rank regression. However, it is difficult to determine the appropriate number of test specimens and censoring intervals required to obtain sufficiently accurate Weibull estimators. In this study, we compare maximum likelihood estimation and median rank regression using a Monte Carlo simulation to examine the effects of the total number of specimens, test duration, censoring interval, and shape parameters of the true Weibull distribution on the estimator uncertainty. Finally, we provide the quantitative uncertainties of both Weibull estimators, compare them with the true Weibull parameters, and suggest proper experimental conditions for developing a probabilistic crack initiation model through crack initiation tests.

5 November 2019 in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
Verified
Journal Article
Closed access
PDF file
JPJae Phil Park
Jae Phil Park
SMSubhasish Mohanty
Subhasish Mohanty
CBChi Bum Bahn
Chi Bum Bahn
SMSaurin Majumdar
Saurin Majumdar
KNKrishnamurti Natesan
Krishnamurti Natesan
In general, fatigue life of a safety critical pressure components is estimated using best-fit fatigue life curves (S~N curves). These curves are estimated based on underlying in-air condition fatigue test data. The best-fitting approach requires large safety factor to accommodate the uncertainty associated with large scatter in fatigue test data. In addition to this safety factor, reactor component fatigue life prognostics requires additional correction factor that in general also estimated deterministically. This additional factor known as environmental correction factor Fen is to cater the effect of harsh coolant environment that severely reduces the life of these components. The deterministic Fen factor may also lead to further conservative estimation of fatigue life leading to unnecessary early retirement of costly reactor components. To address the above-mentioned issues, we propose a data-analytics framework, which uses Weibull and Bootstrap probabilistic modeling techniques for explicitly quantifying the uncertainty/scatter associated with fatigue life rather than estimating the lives based on a best-fit based deterministic approach. We assume the proposed probabilistic approach would provide the firsthand information for assessing the maximum and minimum effect of PWR water on reactor component. In the discussed approach, in addition to the probabilistic fatigue curves, we suggest using a probabilistic environment correction factor Fen. We assume the probabilistic fatigue curve and Fen would capture the S~N data scatter associated with the bulk effect of material grades, surface finish, strain rate, etc. on the material/component fatigue life.

19 July 2021 in Journal of Pressure Vessel Technology
Verified
Journal Article
Closed access
PDF file
JPJae Phil Park
Jae Phil Park
SMSubhasish Mohanty
Subhasish Mohanty
CBChi Bum Bahn
Chi Bum Bahn
At present, the available Ramberg–Osgood (R–O) parameters for different metals (e.g., in ASME code and other literatures) are static (generally based on a tensile curve). These static R–O parameters cannot accurately model the cyclic plasticity behavior. This work presents the cyclic R–O material hardening parameters for 316 stainless steel similar metal welds. The parameters were estimated under various conditions (in-air at room temperature, 300 °C in-air, and in-air at primary water conditions for a pressurized water reactor (PWR)). It is anticipated that the reported results would be useful for computational mechanics-based shakedown analysis and fatigue life estimation of PWR components.

13 January 2026 in PHM Society Asia-Pacific Conference
Verified
Journal Article
Open access
PDF file
SGSewoong Gim
Sewoong Gim
JPJae Phil Park
Jae Phil Park
SLSanghoon Lee
Sanghoon Lee
In power electric (PE) systems of electric vehicles (xEVs), the function of switching power between the battery and inverter is essential for safe operation. This function is performed by the Power Relay Assembly (PRA), which consists of two high-voltage relays (HV relays) that connect the battery’s positive terminals and continuously conduct high current during driving. Unlike low-voltage relays, HV relays are designed with arc-suppression structures and timing control to minimize arc damage, resulting in relatively rare arc erosion failures. However, the passage of high current through the contact interface generates significant heat, leading to material degradation and structural deformation, which have been identified as major failure modes. Such failures can cause abnormal open or short circuits in the high-voltage system, potentially resulting in loss of power control or fires—posing critical safety risks. Therefore, early diagnosis of these failures is essential. HV relays have a sealed design without dedicated cooling, causing heat to accumulate internally under high-current conditions. For effective failure diagnosis, internal thermal monitoring is crucial. However, due to constraints such as limited design space, the need to maintain airtightness, and cost considerations, the number of sensors that can be installed for relay state monitoring is severely limited. As a result, accurately capturing the internal terminal temperature, which is a critical indicator of failure risk, remains challenging. This study proposes the development of a multivariate time-series prediction-based Virtual Thermal Sensor (VTS) [1, 2] model capable of estimating the internal terminal temperature of HV relays using only limited external sensing data available in actual vehicles—such as relay voltage, current, and ambient temperatures. Because the internal temperature evolution depends both on past history and current operating conditions, a Bidirectional Long Short-Term Memory (Bi-LSTM) [3, 4] network was employed to effectively capture these dependencies.diagnostics and remaining useful life (RUL) prediction of high-voltage relays. Future work will focus on refining the VTS model for improved accuracy and reduced computational complexity, supporting the development of practical RUL prediction systems for HV relays. For model training and validation, datasets were collected through high-temperature accelerated life tests of HV relays. The dataset includes time-series measurements of ambient temperature, relay surface temperature, bus-bar temperature, operating voltage, and load current, along with specially instrumented measurements of internal terminal temperature for ground truth validation. To improve prediction accuracy, key influencing variables were selected through correlation analysis, and advanced data preprocessing steps were applied to handle irregular cycles, long-term trends, and saturation regions—ensuring the data’s suitability for modeling. Up to 50% of the total dataset will be reserved for validation, with prediction accuracy to be statistically assessed using metrics such as Root Mean Squared Error (RMSE). This research provides a foundational technology for indirectly estimating the internal terminal temperature—an otherwise difficult-to-measure parameter—enabling degradation diagnostics and remaining useful life (RUL) prediction of high-voltage relays. Future work will focus on refining the VTS model for improved accuracy and reduced computational complexity, supporting the development of practical RUL prediction systems for HV relays.

14 July 2017 in PHM Society Asia-Pacific Conference
Verified
Journal Article
Open access
PDF file
JPJae Phil Park
Jae Phil Park
Chanseok ParkChanseok Park
Chanseok Park
CBChi Bum Bahn
Chi Bum Bahn
Because a large time spread in most crack initiation tests makes it a daunting task to predict the initiation time of cracking, a probabilistic model, such as the Weibull distribution, has been usually employed to model it. In thiscase, although it might be anticipated to develop a more reliable cracking model under ideal cracking test conditions (e.g., large number of specimen, narrow censoring interval, etc.), it is not straightforward to quantitatively assess the effects of these experimental conditions on model estimation uncertainty. Therefore, we studied the effects of some key experimental conditions on estimation uncertainties of the Weibull parameters through the Monte Carlo simulations. Simulation results suggested that the estimated scale parameter would be more reliable than the estimated shape parameter from the tests. It was also shown that increasing the number of specimen would be more efficient to reduce the uncertainty of estimators than the more frequent censoring.