Studies on the ecosystem service value (ESV) of gardens are critical for informing evidence-based land management practices based on an understanding of the local ecosystem. By analyzing equivalent value factors (EVFs), this paper evaluated the values of 11 ecosystem services of gardens in the Yellow River Basin of China in 2019. High-precision land use survey data were used to improve the accuracy of the land use classification, garden areas, and spatial distribution of the ESVs of gardens. The results showed that garden ecosystem generally had high ESVs, especially in terms of the ESV of food production, which is worthy of further research and application to the practice of land use planning and management. Specifically, the value of one standard EVF of ecosystem services in 2019 was 3587.04 CNY/(hm2·a), and the ESV of food production of gardens was much higher than that of croplands. Garden ecosystem provided an ESV of 1348.66×108 CNY/a in the Yellow River Basin. The areas with the most concentrated ESVs of gardens were located in four regions: downstream in the Shandong-Henan zone along the Yellow River, mid-stream in the Shanxi-Shaanxi zone along the Yellow River, the Weihe River Basin, and upstream in the Qinghai-Gansu-Ningxia-Inner Mongolia zone along the Yellow River. The spatial correlation of the ESVs in the basin was significant (global spatial autocorrelation index Moran’s I=0.464), which implied that the characteristics of high ESVs adjacent to high ESVs and low ESVs adjacent to low ESVs are prominent. In the Yellow River Basin, the contribution of the ESVs of gardens to the local environment and economy varied across regions. We also put forward some suggestions for promoting the construction of ecological civilization in the Yellow River Basin. The findings of this study provide important contributions to the research of ecosystem service evaluation in the Yellow River Basin.
For fault-controlled fractured-vuggy reservoirs, the development characteristics of bottom water flooding and water and gas injection flooding under multi-well conditions must be clarified due to the structural complexity. To address this issue, we designed and manufactured fault-controlled physical experimental models based on the geological model of Tarim Oilfield and conducted flooding experiments. The results demonstrate significant variations in bottom water flooding characteristics due to differences in flow capacity within fractures, cavity area in caves, and filled area in caves under different filling modes. Different bottom water rates exhibit varying abilities to overcome gravity and breakthrough capillary resistance, significantly impacting the bottom water flooding characteristics. During the bottom water flooding period, the positioning of production wells primarily affects the macroscopic sweep range, while the filling modes significantly influence the distribution of remaining oil within individual caves. Throughout the three periods of multi-well water and gas injection, the early water injection stage mainly focuses on mobilizing “insufficiently controlled remaining oil” and some “attic remaining oil,” and the middle gas injection stage primarily targets the attic remaining oil. Finally, the late water injection stage aims to lift the oil–gas–water interface and improve oil displacement efficiency. Furthermore, different water and gas flooding directions affect displacement resistance in each channel and the longitudinal sweep range. This paper identifies the direction for the life cycle production of fault-controlled fractured-vuggy reservoirs and presents a mechanistic explanation.
Summary: Thermal recovery techniques serve as the primary approach for developing heavy oil due to its high viscosity and poor flowability. In this study, we established a high-temperature and high-pressure 3D physical experimental and numerical model based on the unique reservoir characteristics of the sand-mud interlayer in the Long Lake oil sands of Canada, using similarity criteria. Physical and numerical experiments employing steam-assisted gravity drainage (SAGD) were conducted to investigate the impact of sand-mud interlayer properties on the expansion limit of steam chambers during SAGD development. The results indicate that the expansion mode and limit of the steam chamber play a decisive role in heavy oil mobilization. Notably, heat loss during steam chamber expansion and the flow resistance caused by the interlayer are critical factors influencing the SAGD process. The presence of the interlayer extends the mobilization range in the lower portion of the reservoir, but it also limits the upward expansion of the steam chamber, resulting in a reduced mobilization range above the interlayer. Moreover, the steam chamber above the interlayer exhibits a distinct expansion pattern, featuring concave sides and a convex middle, resembling a “positive triangle.” Furthermore, the properties of the sand-mud interlayer and production parameters significantly affect the expansion limit of the steam chamber. Permeability and position exert a substantial impact on recovery, whereas thickness has a minor influence. Specifically, at an injection rate of 20 mL·min–1, steam quality of approximately 0.7, and a production/injection ratio of approximately 1.0, the steam chamber can successfully penetrate interlayers with a thickness of either 3.5 m and a permeability of 100×10−3 μm2 or 4.5 m and a permeability of 200×10−3 μm2.
Dynamic capillary pressure plays a critical role in understanding fluid displacement in low-permeability reservoirs, particularly under non-equilibrium conditions during forced imbibition. This study introduces a novel experimental apparatus and methodology to quantify dynamic and quasi-static capillary pressure behaviors in water-wet porous media. Core samples from a low-permeability water-wet reservoir were subjected to varying injection rates, permeability ranges, and oil–water viscosity ratios using brine and crude oil as the fluid pair. Key findings reveal that dynamic capillary pressure (Pcd) consistently lies below quasi-static capillary pressure (Pcqs) across all experimental conditions, with the gap increasing under higher injection rates. Notably, negative Pcqs and Pcd values were observed during forced imbibition, a unique phenomenon warranting further investigation. Dimensionless analysis and curve fitting yielded a quasi-dynamic coefficient model that captures the transient capillary effects as a function of permeability, viscosity ratio, and injection velocity. The model demonstrated high accuracy (R2 ≈ 0.85) in predicting dynamic capillary pressure behavior. Experimental and fitted results highlight the significant influence of displacement velocity on dynamic effects, with stronger effects observed in low-permeability samples. This study advances the understanding of capillary pressure dynamics in low-permeability systems, providing a robust framework for improved reservoir simulation and enhanced oil recovery strategies.
The temporal and spatial variation of ecological land use and its current distribution were studied to provide reference for the protection of original ecological land and ecological environment in the Yellow River Delta. Using RS colour synthesis, supervised classification, unsupervised classification, vegetation index and other methods to monitor the impact of human activities on the original ecological land in the past 30 years; using GIS technology to analyse the statistical data and construct the model of original ecological land area index to study the ecological land distribution status. The results show that the boundary of original ecological land in the Yellow River Delta had been pushed toward the coastline at an average speed of 0.8km per year due to human activities. In the past 20 years, a large amount of original ecological land gradually transformed into artificial ecological land. In view of the evolution and status of ecological land in the Yellow River Delta, related local departments should adopt differentiated and focused protection measures to protect the ecological land of the Yellow River Delta.
2 December 2024 in Petroleum Science and Technology