A switched-capacitor bidirectional dc-dc converter with a high step-up/step-down voltage gain is proposed for electric vehicles with a hybrid energy source system. The converter presented has the advantages of being a simple circuit, a reduced number of components, a wide voltage-gain range, a low voltage stress, and a common ground. In addition, the synchronous rectifiers allow zero voltage switching turn-on and turn-off without requiring any extra hardware, and the efficiency of the converter is improved. A 300 W prototype has been developed, which validates the wide voltage-gain range of this converter using a variable low-voltage side (40-100 V) and to give a constant high-voltage side (300 V). The maximum efficiency of the converter is 94.45% in step-down mode and 94.39% in step-up mode. The experimental results also validate the feasibility and the effectiveness of the proposed topology.

In fuel cell vehicles, the output voltage of the fuel cell source is typically much lower than the voltage required by the DC bus and also this output voltage drops significantly as the output current increases. In order to match the output voltage of the fuel cell source to the DC bus voltage, a new DC-DC boost converter with a wide input range and high voltage gain is proposed to act as the required power interface, which reduces voltage stress across the power devices and operates with an acceptable conversion efficiency. A prototype rated at 300W/400V has been developed and the maximum efficiency of the proposed converter was measured as 95.01% at 300W. Experimental results are presented to validate the effectiveness of the proposed converter.

In this paper, an interleaved switched-capacitor bidirectional dc-dc converter with a high step-up/step-down voltage gain is proposed. The interleaved structure is adopted in the low-voltage side of this converter to reduce the ripple of the current through the low-voltage side, and the series-connected structure is adopted in the high-voltage side to achieve the high step-up/step-down voltage gain. In addition, the bidirectional synchronous rectification operations are carried out without requiring any extra hardware, and the efficiency of the converter is improved. Furthermore, the operating principles, voltage and current stresses, and current ripple characteristics of the converter are analyzed. Finally, a 1 kW prototype has been developed which verifies a wide voltage-gain range of this converter between the variable low-voltage side (50–120 V) and the constant high-voltage side (400 V). The maximum efficiency of the converter is 95.21% in the step-up mode and 95.30% in the step-down mode. The experimental results also validate the feasibility and the effectiveness of the proposed topology.

In this paper, a hybrid switched-capacitor/ switched-quasi-Z-source bidirectional dc-dc converter is proposed for electric vehicles (EVs) with hybrid energy sources, which has a wide voltage gain range in the bidirectional energy flows. Compared with the traditional quasi-Z-source bidirectional dc-dc converter, the proposed converter only changes the position of the main power switch, and employs a switched-capacitor cell at the output of the high voltage side. Therefore, the advantages of the wide voltage gain range and the lower voltage stresses across the power switches can be achieved. The operating principle, the voltage and current stresses across the power switches and the comparisons with other converters are analyzed in detail. Furthermore, the parameter design of the main components, the dynamic modelling analysis and the voltage control scheme are also presented. Finally, the experimental results obtained from a 400W prototype validate the characteristics and the theoretical analysis of the proposed converter.

A quasi-Z-source boost dc–dc converter, which uses a switched capacitor, is proposed for fuel cell vehicles. The topology can obtain a high-voltage gain with a wide input-voltage range and requires only a low-voltage stress across each of the components. The performance of the proposed converter is compared with other converters which use Z-source networks. A scaled-down 400-V/400-W prototype is developed to validate the proposed technology. The respective variation in the output voltage is avoided when the wide variation in the input voltage happens, due to the PI controller in the voltage loop, and a maximum efficiency of 95.13% is measured.

A common ground switched-quasi-Z-source bidirectional dc-dc converter is proposed for electric vehicles with hybrid energy sources. The proposed converter is based on the traditional two-level quasi-Z-source bidirectional dc-dc converter, changing the position of the main power switch. It has the advantages of a wide-voltage-gain range, a lower voltage stress across the power switches, and an absolute common ground. The operating principle, the voltage and current stresses on the power switches, the comparisons with the other converters, the small signal analysis, and the controller design are presented in this paper. Finally, a 300 W prototype with U _high = 240 V and U _low = 40~120 V is developed, and the experimental results validate the performance and the feasibility of the proposed converter.