Niobium dioxide (NbO2) features a high theoretical capacity and an outstanding electron conductivity, which makes it a promising alternative to the commercial graphite negative electrode. However, studies on NbO2 based lithium‐ion battery negative electrodes have been rarely reported. In the present work, NbO2 nanoparticles homogeneously embedded in a carbon matrix are synthesized through calcination using a dental resin monomer (bisphenol A glycidyl dimethacrylate, Bis‐GMA) as the solvent and a carbon source and niobium ethoxide (NbETO) as the precursor. It is revealed that a low Bis‐GMA/NbETO mass ratio (from 1:1 to 1:2) enables the conversion of Nb (V) to Nb (IV) due to increased porosity induced by an alcoholysis reaction between the NbETO and Bis‐GMA. The as‐prepared NbO2/carbon nanohybrid delivers a reversible capacity of 225 mAh g−1 after 500 cycles at a 1 C rate with a Coulombic efficiency of more than 99.4% in the cycles. Various experimental and theoretical approaches including solid state nuclear magnetic resonance, ex situ X‐ray diffraction, differential electrochemical mass spectrometry, and density functional theory are utilized to understand the fundamental lithiation/delithiation mechanisms of the NbO2/carbon nanohybrid. The results suggest that the NbO2/carbon nanohybrid bearing high capacity, long cycle life, and low gas evolution is promising for lithium storage applications.
In this study, three copolymers of poly(methyl methacrylate) and poly(butyl acrylate) (PMMA-co-PBA) latex containing 1-octyl-3 methylimidazolium hexafluorophosphate (C8mimPF6), cellulose nanocrystals (CNCs), and C8mimPF6-CNCs were successfully synthesized through mini emulsion polymerization. These novel composites were each coated on mild steel panels and tested for their anti-corrosion performance by immersion of the coated samples in 3.5 wt% sodium chloride (NaCl) solution over a certain period. The synergistic anti-corrosion effects of the C8mimPF6-CNCs sample led to the highest coating resistance, charge transfer resistance, and corrosion inhibition efficiency and the lowest diffusion coefficient and corrosion rate. The proposed synergistic mechanism revealed that CNCs enhanced the barrier effect of the coating while C8mimPF6 inhibited corrosion when released.
Poly(N-isopropylacrylamide) (polyNIPAm) microspheres were synthesized via the suspension polymerization technique. Thermal and redox initiators were compared for the polymerization, in order to study the effect of initiator type on the surface charge and particle size of polyNIPAm microspheres. The successful polymerization of NIPAm was confirmed by FTIR analysis. Microspheres of diameter >50 µm were synthesized when a pair of ammonium persulfate (APS) and N,N,N’,N’-tetramethylene-diamine (TEMED) redox initiators was used, whilst relatively small microspheres of ~1 µm diameter were produced using an Azobis-isobutyronitrile (AIBN) thermal initiator. Hence, suspension polymerization using a redox initiator pair was found to be more appropriate for the synthesis of polyNIPAm microspheres of a size suitable for human embryonic kidney (HEK) cell culturing. However, the zeta potential of polyNIPAm microspheres prepared using an APS/TEMED redox initiator was significantly more negative than AIBN thermal initiator prepared microspheres and acted to inhibit cell attachment. Conversely, strong cell attachment was observed in the case of polyNIPAm microspheres of diameter ~90 µm, prepared using an APS/TEMED redox initiator in the presence of a cetyl trimethyl ammonium bromide (CTAB) cationic surfactant; demonstrating that surface charge modified polyNIPAm microspheres have great potential for use in cell culturing.
24 May 2025 in International Journal of Biological Macromolecules