Wireless power transfer (WPT) is a promising solution to provide convenient and perpetual energy supplies to electronics. Traditional WPT technologies face the challenge of providing Watt-level power over meter-level distance for Internet of Things (IoT) and mobile devices, such as sensors, controllers, smart-phones, laptops, etc.. Distributed laser charging (DLC), a new WPT alternative, has the potential to solve these problems and enable WPT with the similar experience as WiFi communications. In this paper, we present a multi-module DLC system model, in order to illustrate its physical fundamentals and mathematical formula. This analytical modeling enables the evaluation of power conversion or transmission for each individual module, considering the impacts of laser wavelength, transmission attenuation and photovoltaic-cell (PV-cell) temperature. Based on the linear approximation of electricity-to-laser and laser-to-electricity power conversion validated by measurement and simulation, we derive the maximum power transmission efficiency in closed-form. Thus, we demonstrate the variation of the maximum power transmission efficiency depending on the supply power at the transmitter, laser wavelength, transmission distance, and PV-cell temperature. Similar to the maximization of information transmission capacity in wireless information transfer (WIT), the maximization of the power transmission efficiency is equally important in WPT. Therefore, this work not only provides the insight of DLC in theory, but also offers the guideline of DLC system design in practice.

The existing channel estimation methods for millimeter-wave (mmWave) communications, e.g., hierarchical search and compressed sensing (CS), either acquire only one single multipath component (MPC) or require considerably high training overhead. To realize fast yet accurate channel estimation, we propose a multipath decomposition and recovery (MDR) approach in this paper. The proposed approach has two stages. In the first stage, instead of directly searching the real MPCs, we decompose each real MPC into several virtual MPCs, and acquire the virtual MPCs by using the hierarchical search based on a normal-resolution codebook. Then in the second stage, the real MPCs are recovered from the acquired virtual MPCs in the first stage, which turns out to be a sparse reconstruction problem, where the size of the dictionary matrix is greatly reduced by exploiting the results of the virtual multipath acquisition. Moreover, to make the proposed approach applicable for both analog and hybrid beamforming/combining devices with strict constant-modulus constraint, we particularly design a codebook for the hierarchical search by using an enhanced sub-array technique, and the codebook is also applicable in other hierarchical search methods. Performance comparisons show that the proposed approach achieves a superior tradeoff between estimation performance and training penalty over the state-of-the-art alternatives.

In this paper, we study beamforming based full-duplex (FD) systems in millimeter-wave (mmWave) communications. A joint transmission and reception (Tx/Rx) beamforming problem is formulated to maximize the achievable rate by mitigating self-interference (SI). Since the optimal solution is difficult to find due to the non-convexity of the objective function, suboptimal schemes are proposed in this paper. A low-complexity algorithm, which iteratively maximizes signal power while suppressing SI, is proposed and its convergence is proven. Moreover, two closed-form solutions, which do not require iterations, are also derived under minimum-mean-square-error (MMSE), zero-forcing (ZF), and maximum-ratio transmission (MRT) criteria. Performance evaluations show that the proposed iterative scheme converges fast (within only two iterations on average) and approaches an upper-bound performance, while the two closed-form solutions also achieve appealing performances, although there are noticeable differences from the upper bound depending on channel conditions. Interestingly, these three schemes show different robustness against the geometry of Tx/Rx antenna arrays and channel estimation errors.

Resonant Beam Charging (RBC) is the Wireless Power Transfer (WPT) technology, which can provide high-power, long-distance, mobile, and safe wireless charging for Internet of Things (IoT) devices. Supporting multiple IoT devices charging simultaneously is a significant feature of the RBC system. To optimize the multi-user charging performance, the transmitting power should be scheduled for charging all IoT devices simultaneously. In order to keep all IoT devices working as long as possible for fairness, we propose the First Access First Charge (FAFC) scheduling algorithm. Then, we formulate the scheduling parameters quantitatively for algorithm implementation. Finally, we analyze the performance of FAFC scheduling algorithm considering the impacts of the receiver number, the transmitting power and the charging time. Based on the analysis, we summarize the methods of improving the WPT performance for multiple IoT devices, which include limiting the receiver number, increasing the transmitting power, prolonging the charging time and improving the single-user’s charging efficiency. The FAFC scheduling algorithm design and analysis provide a fair WPT solution for the multi-user RBC system.

Resonant beam charging (RBC) can realize wireless power transfer (WPT) from a transmitter to multiple Internet of things (IoT) devices via resonant beams. The adaptive RBC (ARBC) can effectively improve its energy utilization. In order to support multi-user WPT in the ARBC system, we propose the time-division multiple access (TDMA) method and design the TDMA-based WPT scheduling algorithm. Our TDMA WPT method has the features of concurrently charging, continuous charging current, individual user power control, constant driving power and flexible driving power control. The simulation shows that the TDMA scheduling algorithm has high efficiency, as the total charging time is roughly half (46.9% when charging 50 receivers) of that of the alternative scheduling algorithm. Furthermore, the TDMA for WPT inspires the ideas of enhancing the ARBC system, such as flow control and quality of service (QoS).

As a long-range high-power wireless power transfer (WPT) technology, resonant beam charging (RBC) can transmit Watt-level power over long distance for the devices in the internet of things (IoT). Due to its open-loop architecture, RBC faces the challenge of providing dynamic current and voltage to optimize battery charging performance. In RBC, battery overcharge may cause energy waste, thermal effects, and even safety issues. On the other hand, battery undercharge may lead to charging time extension and significant battery capacity reduction. In this paper, we present an adaptive resonant beam charging (ARBC) system for battery charging optimization. Based on RBC, ARBC uses a feedback system to control the supplied power dynamically according to the battery preferred charging values. Moreover, in order to transform the received current and voltage to match the battery preferred charging values, ARBC adopts a direct current to direct current (DC-DC) conversion circuit. Relying on the analytical models for RBC power transmission, we obtain the end-to-end power transfer relationship in the approximate linear closed-form of ARBC. Thus, the battery preferred charging power at the receiver can be mapped to the supplied power at the transmitter for feedback control. Numerical evaluation demonstrates that ARBC can save 61% battery charging energy and 53%-60% supplied energy compared with RBC. Furthermore, ARBC has high energy-saving gain over RBC when the WPT is unefficient. ARBC in WPT is similar to link adaption in wireless communications. Both of them play the important roles in their respective areas.