The nondestructive detection of kiwifruit texture has become an important necessity that influences kiwifruit economic efficiency and consumer recognition of the kiwifruit. This study investigated the feasibility of using hyperspectral imaging technology to identify textural characteristics of kiwifruit, and to establish the model with best performance. Firstly, a near-infrared hyperspectral online grading system (1000–2500 nm) was constructed to acquire spectral images. Textural characteristics were measured via three different textural analysis tests: textural profile analysis, puncture test, and shear test. Then, samples were divided into a calibration set and a prediction set based on rank sampling at a ratio of 3:1. Mean centralization, standard normal variate, and multiplicative scatter correction methods were applied to pre-process obtained spectra. Finally, the partial least squares method was used to establish prediction models of kiwifruit textural characteristics. The models of hardness1, chewiness, resilience, peel hardness, average hardness, and corrected hardness achieved good performance. Both the correlation coefficients of calibration (rc) and prediction (rp) values exceeded 0.9. The difference between the root mean square error (RMSE) of calibration and prediction was small, and the ratio of prediction to deviation (RPD) value exceeded 2, which was used to predict kiwifruit quality. However, the model of average shear force had a low accuracy with an RPD of 1.680 and the model of shear force also had an RPD below 1.5 and a low RMSE. The results showed that near-infrared hyperspectral imaging technique can be used as a nondestructive method for the textural characteristics kiwifruit.
Chinese missions to the moon are planned to sample the regolith and return it to the earth. Microscale excavators may be good candidates for these missions, as they would significantly reduce the launch mass. Thus, it is necessary to research the interaction between the scoop and the regolith being sampled. We present the development of a simple apparatus to measure excavation torque. All tests were conducted using TYII-2 regolith simulant with gravels. The test results show that, under loose regolith conditions, the penetrating angle and the bulk density had a great influence on the excavation torque, while the rotating speed had little effect. However, when the bulk density was compact, the rotating speed did influence the excavation torque. The excavation torque increased sharply when the scoop encountered the gravels; actually, some of the parameters will influence the value of the torque such as the diameter, quantity, and position and inbuilt depth of the gravels. When the excavation torque sharply increases, the operation should be immediately stopped and checked.
In order to improve the traction performance of a wheel of a micro-tiller on the soil surface of a paddy field, we extracted the surface curve of a cow’s hoof and used the cow’s hoof as a bionic prototype to design a bionic paddy wheel. In order to verify the passability of the bionic paddy wheel in paddy soil, a wheel-soil test bench was built in the experimental field with a moisture content of 36%. The test results show that under the condition of the same load on the wheel, the changing laws of torque, drawbar pull, and slip ratio of the bionic paddy wheel and the conventional vaned wheel are similar. The torque and drawbar pull of the bionic paddy wheel are higher than those of the conventional vaned wheel at the same slip ratio. The maximum torque and hook traction provided by the bionic paddy wheel and the conventional vaned wheel both increase with the increase of the load on the wheel. Under the same load on the wheel, the bionic paddy wheel is at least 22% higher than the conventional vaned wheel. Compared with the conventional vaned wheel, the bionic paddy wheel can provide a higher driving force and hook traction, which can improve the working efficiency of the vehicle in the paddy field.
It suggests that a high leptin level may increase the risk of venous thromboembolism (VTE) in animal studies. However, clinical studies in this field are still largely unexplored. Our objective was to evaluate the relationship between the preoperative serum leptin levels and postoperative VTE incidence in osteoarthritis (OA) patients who underwent total knee arthroplasty (TKA) at our institute. We conducted a prospective and cross-sectional study in these OA patients from March 2014 to March 2016. Preoperative leptin levels were analyzed by Luminex assays. VTE was assessed preoperatively and on postoperative day 5 and 7. The potential risk factors for VTE were also documented. We enrolled 203 OA patients. No PE was detected and DVT was diagnosed in 34 patients postoperatively. There were significant differences between the median leptin levels in DVT group and non-DVT group [25.13 ng/mL (interquartile range, 14.51–44.31) vs 18.71 ng/mL (8.26–28.99), P = .007]. The relative risk of DVT significantly increased with natural logarithm (ln) leptin (per SD increase) (OR 2.37, 95% confidence interval (95% CI), 1.29–4.33, P = .005). Multivariate analyses adjusted for potential confounders showed ln leptin (per SD increase) was significantly associated with the relative risk of DVT (OR 2.17, 95% CI, 1.01–4.64, P = .046). When patients were subdivided into tertiles according to their leptin values, the OR for DVT increased with increasing tertiles of serum leptin (OR 1.03, 95% CI, 1.01–1.06, P for trend = .023). In the present study, our results indicate that a high preoperative leptin level may be an independent risk factor for postoperative DVT.
Canker is a common disease of navel oranges that is visible before harvest, and penicilliosis is a common disease occurring after harvest and storage. In this research, the typical fruit surface, canker spots, penicillium spore, and hypha of navel oranges were, respectively, identified by hyperspectral imaging. First, the light intensity on the edge of samples in hyperspectral images was improved by spherical correction. Then, independent component images and weight coefficients were obtained using independent component analysis. This approach, combined with use of a genetic algorithm, was used to select six characteristic wavelengths. The method achieved dimension reduction of hyperspectral data, and the testing time was reduced from 46.21 to 1.26 s for a self-developed online detection system. Finally, a deep learning neural network model was established, and the four kinds of surface pixels were identified accurately.