Objective: The purpose of this study was to investigate and quantify flow properties, compressibility, and compactibility of various pharmaceutical lactose powders found on the market today (DCL-11, DCL-21, M‐200, Flowlac-100, and Tablettose 70, 80, and 100). Methods: Flow properties were estimated by measuring flow time, angle of repose, and the Hausner ratio. Particle rearrangement was studied using Kawakita's linear model. Compressibility was studied using two ‘out-of-die’ methods: (i) the Heckel model and (ii) a modified Walker model. Compactibility was quantified using two methods: (i) the tensile strength profile (Cp) and (ii) the compactibility factor (Pr). Statistical approach was used to analyze the results. Results: Flow properties of all materials were passable or better, except for M-200, which has very poor flowability. Compressibility results demonstrated that the most compressible lactose is spray-dried grade of lactose (Flowlac-100) and the least compressible is milled lactose (M-200). Compactibility studies showed that β‐lactose (DCL-21) forms tablets with superior tensile strength in comparison with α-lactose. Conclusion: Results of the compressibility study showed that the discriminative power of modified Walker model is greater in comparison with Heckel model. Compactibility methods yield similar and comparable results.
28 September 2011 in Drug Development and Industrial Pharmacy
Objective: In this study, different modifications of bottom spray fluid-bed coater with draft tube inserted were characterized and evaluated. Materials and methods: After coating the neutral pellets with polymeric solution comprising coloring agent pellet batches were characterized for coating variation, yield and degree of agglomeration. Results: Funnel-shaped distribution plate was found to improve process yield and decrease the degree of agglomeration at selected values of process parameters, whereas coating uniformity was worse in all cases when compared to conventional Wurster chamber. Results of the coating chamber with the swirl airflow generator indicate more uniform deposition of the coating material and in some cases an improved process yield and decreased formation of agglomerates when compared to conventional Wurster chamber. In series of experiments using Wurster chamber, having tangentially oriented air intake slots, which enabled introduction of air above the distribution plate, coating layer was more uniformly deposited on the pellet cores and formation of agglomerates was lower compared to the results obtained in a conventional Wurster coating chamber. Conclusion: Modifications of Wurster coating process by introducing swirling air motion within the draft tube or by introduction of air above the distribution plate have at selected values of process parameters resulted in reduced per-particle coating variation, degree of agglomeration and improved process yield.
Binder jetting has the potential to revolutionize the way we produce medicine. However, tablets produced by binder jetting technology can be quite fragile and hard to handle. In this study, the printing process and ink composition were examined to optimize the mechanical properties of tablets. A model formulation containing the ketoprofen drug was developed and used as a base for optimization. Firstly, important printing parameters were identified with a fractional factorial design. Saturation and layer height critically influenced selected tablet properties. Relevant process parameters were optimized for tablet mechanical strength by using the D-optimization DoE approach. The best mechanical properties were achieved when saturation was set to 1 and layer height to 150 µm. On the other hand, binder ink composition did not appear to impact tablet mechanical strength as much as process parameters did. Three ethanol-water mixtures were tested at three tablet strength levels and no definitive conclusions could be drawn. The binder jetting process can be wasteful, especially if the unbound powder cannot be reused. To determine the suitability of powder blend recycling, the ketoprofen content was measured for 27 subsequent batches of tablets. While the trendline did indicate a slight reduction in ketoprofen content, the powder blend reuse can nevertheless be employed.
1 July 2015 in European Journal of Pharmaceutical Sciences
This study evaluated the performance of two bottom-spray coaters and the effect of pellet-size variability on coating uniformity. A conventional Wurster chamber was used for the first group of trials, and a Wurster chamber with a novel swirl-flow generator design was used for the second. The results confirmed that when using a conventional Wurster coating chamber, pellets with a smaller diameter receive significantly less coating material compared to those with larger diameters. The swirl generator-equipped Wurster chamber achieved close to uniform coating thickness regardless of pellet size. The ratio (MS) of the mass of dye deposited in the coating layer to pellet surface area indicates that coating was much more evenly distributed using the swirl-flow coater. Coating thickness was also analyzed using SEM micrographs and the results were in close agreement with the MS factor values. Inter-particle coating mass variation was also lower in case of swirl-flow coater. The results of this study show that a swirl-flow coater is suitable for coating particles of variable size. They also showed an improvement in coating process yield when using the swirl-flow coater.
31 January 2009 in African Journal of Pharmacy and Pharmacology
Paracetamol (PAR) crystals exhibit poor compressibility, poor flowability and its tablets show a tendency to cap. To improve the mechanical strength of tablets several kinds of “Paracetamol for direct compression” are present on the market. Current research demonstrated the best tablet properties with coated paracetamol (mass of tablets, diameter, height and mechanical strength, friability RSD<2%). Furthermore, coated paracetamol in combination with both investigated superdisintegrants such as Vivasol®and Polyplasdone® XL-10 shows faster disintegration time and dissolution rate in comparison to paracetamol for direct compression. Eventually, the major advantages of the formulation with coated paracetamol for industrial production are decrease of friability and superiority in terms of flowability, compressibility, quick disintegration and dissolution. Regarding the results, coating of PAR particles is beneficial for the manufacturing of tablets with immediate release. Key words: Paracetamol, powder, direct compression, immediate release, superdisintegrants.