Polymer electrolyte fuel cells with alkaline anion exchange membranes (AAEMs) have gained increasing attention because of the faster reaction kinetics associated with the alkaline environment compared to acidic media. While the development of anion exchange polymer membranes is increasing, the catalytic layer structure and composition of electrodes is of paramount importance to maximize fuel cell performance. In this work, we examine the preparation procedures for electrodes by catalyst-coated substrate to be used with a well-known commercial AAEM, Fumasep® FAA-3, and a commercial ionomer of the same nature (Fumion), both from Fumatech GmbH. The anion exchange procedure, the ionomer concentration in the catalytic layer and also the effect of membrane thickness, are investigated as they are very relevant parameters conditioning the cell behavior. The best power density was achieved upon ion exchange of the ionomer by submerging the electrodes in KCl (isopropyl alcohol/water solution) for at least one hour, two exchange steps, followed by treatment in KOH for 30 min. The optimum ionomer (Fumion) concentration was found to be close to 50 wt%, with a relatively narrow interval of functioning ionomer percentages. These results provide a practical guide for electrode preparation in AAEM-based fuel cell research.
In this work, palladium-nickel nanoparticles supported on carbon nanofibers were synthesized, with metal contents close to 25 wt % and Pd:Ni atomic ratios near to 1:2. These catalysts were previously studied in order to determine their activity toward the oxygen reduction reaction. Before the deposition of metals, the carbon nanofibers were chemically treated in order to generate oxygen and nitrogen groups on their surface. Transmission electron microscopy analysis (TEM) images revealed particle diameters between 3 and 4 nm, overcoming the sizes observed for the nanoparticles supported on carbon black (catalyst Pd-Ni CB 1:2). From the CO oxidation at different temperatures, the activation energy Eact for this reaction was determined. These values indicated a high tolerance of the catalysts toward the CO poisoning, especially in the case of the catalysts supported on the non-chemically treated carbon nanofibers. On the other hand, apparent activation energy Eap for the methanol oxidation was also determined finding—as a rate determining step—the COads diffusion to the OHads for the catalysts supported on carbon nanofibers. The results here presented showed that the surface functional groups only play a role in the obtaining of lower particle sizes, which is an important factor in the obtaining of low CO oxidation activation energies.
Different advanced nanostructured carbon materials, such as carbon nanocoils, carbon nanofibers, graphitized ordered mesoporous carbons and carbon xerogels, presenting interesting features such as high electrical conductivity and extensively developed porous structure were synthesized and used as supports in the preparation of electrocatalysts for direct methanol fuel cells (DMFCs). The main advantage of these supports is that their physical properties and surface chemistry can be tailored to adapt the carbonaceous material to the catalytic requirements. Moreover, all of them present a highly mesoporous structure, diminishing diffusion problems, and both graphitic character and surface area can be conveniently modified. In the present work, the influence of the particular features of each material on the catalytic activity and stability was analyzed. Results have been compared with those obtained for commercial catalysts supported on Vulcan XC-72R, Pt/C and PtRu/C (ETEK). Both a highly ordered graphitic and mesopore-enriched structure of these advanced nanostructured materials resulted in an improved electrochemical performance in comparison to the commercial catalysts assayed, both towards CO and alcohol oxidation.
The increasing interest towards greener antioxidants obtained via natural sources and more sustainable processes encourages the development of new theoretical and experimental methods in the field of those compounds. Two advanced separation methods using supercritical CO2 are applied to obtain valuable antioxidants from Salvia officinalis, and a first approximation to a QSAR model relating molecular structure with antioxidant activity is explored in order to be used, in the future, as a guide for the preselection of compounds of interest in these processes. Separation experiments through antisolvent fractionation with supercritical CO2 were designed using a Response Surface Methodology to study the effect of pressure and CO2 flow rate on both mass yields and capability to obtain fractions enriched in three antioxidant compounds: chlorogenic acid, caffeic acid and rosmarinic acid which were tracked using HPLC PDA. Rosmarinic acid was completely retained in the precipitation vessel while chlorogenic and caffeic acids, though distributed between the two separated fractions, had a major presence in the precipitation vessel too. The conditions predicted for an optimal overall yield and enrichment were 148 bar and 10 g/min. Although a training dataset including much more compounds than those now considered can be recommended, descriptors calculated from the σ-profiles provided by COSMO-RS model seem to be adequate for estimating the antioxidant activity of pure compounds through QSAR.
30 November 2010 in Journal of Chemical & Engineering Data