A path to lowering the economic barrier associated with the high cost of metal additively manufactured components is to reduce the waste via powder reuse (powder cycled back into the process) and recycling (powder chemically, physically, or thermally processed to recover the original properties) strategies. In electron beam powder bed fusion, there is a possibility of reusing 95–98% of the powder that is not melted. However, there is a lack of systematic studies focusing on quantifying the variation of powder properties induced by number of reuse cycles. This work compares the influence of multiple reuse cycles, as well as powder blends created from reused powder, on various powder characteristics such as the morphology, size distribution, flow properties, packing properties, and chemical composition (oxygen and nitrogen content). It was found that there is an increase in measured response in powder size distribution, tapped density, Hausner ratio, Carr index, basic flow energy, specific energy, dynamic angle of repose, oxygen, and nitrogen content, while the bulk density remained largely unchanged.
2 June 2020 in Journal of Manufacturing Science and Engineering
The master sinter curve (MSC) is an empirical model used to predict the density of a part after being sintered. The model is typically applied to components that undergo isotropic shrinkage. Parts manufactured using binder jetting additive manufacturing (BJAM) are known to have nonuniform powder systems and high levels of anisotropy. This work explores the application of the master sinter curve to components made by BJAM. Cylindrical samples were manufactured with the long axis parallel (vertical), perpendicular (horizontal), and 45 deg to the printing direction. A bimodal blend of titanium powder (0–45 µm and 106–150 µm) was used to make samples with consistent green densities (ranging from 47.2% to 52.3%) between the different orientations. Samples were then sintered at heating rates of 1, 3, and 5 °C/min to a maximum of 1400 °C. After sintering, the samples showed significant variation between the different orientations, with vertical samples on average 7.6 ± 2.98% and 4.7 ± 1.20% denser than the horizontal and the 45 deg samples, respectively. The calculated apparent activation energies for sintering were within the same range for all orientations, 200–260 kJ/mol for vertical and 45 deg, and 140–260 kJ/mol for horizontal samples. Validation sinter runs showed that the density prediction errors of the master sinter curves were between 0.9% and 4.3%. This work shows that the master sinter curve can be applied to predict the sintered density of components manufactured by binder jetting additive manufacturing.
Additive manufacturing quality assessment often relies on tensile testing as the preferred methodology to qualify builds and materials. The data included in this article provides additional supporting information on our manuscript (Shanbhag et al., 2021) on the effect of specimen geometry and orientation on tensile properties of Ti-6Al-4V manufactured by electron beam powder bed fusion. As such, the data in brief provides in-depth details on the tensile specimen specifications, the tensile specimen build layout and replicate notations, and the tensile testing datasets. The information presented herein complements the manuscript.
31 December 2024 in The Canadian Journal for the Scholarship of Teaching and Learning
Mental health literacy is an important factor in caring for mental health; however, in the post-secondary student population, mental health literacy is reported to be low. To address these issues, in 2020, one of the authors [CZ] developed an undergraduate mental health literacy (MHL) course offered through the Faculty of Health, University of Waterloo, to undergraduate students in all Faculties. Building on promising early research conducted by two of the authors in 2021, we conducted three studies to evaluate the impacts of the fully online version of this MHL course. Study #1 was a pre-post study to examine knowledge and attitudes related to mental health literacy (n = 162). Study #2 was a one-month follow-up study to assess continued use of mental wellness strategies practiced during the course (n = 18), and study #3 was a content analysis of part one of the final reflection assignment of the course (n = 32). The pre-post study did not reveal any meaningful changes in knowledge and attitude from Time 1 to Time 2. However, the one-month follow-up study and the content analysis of the final reflection assignment showed multiple meaningful and positive shifts in knowledge, attitudes, and behaviours related to mental health, stigma, self-care, well-being, supporting others with mental health concerns, and the meaning of resilience. In addition, the content analysis revealed that students were sharing course resources with peers, friends, family members and with their community at large. In addition to guiding revisions to strengthen the MHL course under investigation, our findings are relevant to other MHL education initiatives in this population.