The control of the solidification structure of a casting billet is directly correlated with the quality of steel. Variations in superheat can influence the transition from columnar crystals to equiaxed crystals during the solidification process, subsequently impacting the final solidification structure of the billet. In this study, a model of microstructure evolution during billet solidification was established by combining simulation and experiment, and the dendrite growth microstructure evolution during billet solidification under different superheat was studied. The results show that when the superheat is 60 K, the complete solidification time of the casting billet from the end of the 50 mm section is 252 s, when the superheat is 40 K, the complete solidification time of the casting billet is 250 s, and when the superheat is 20 K, the complete solidification time of the casting billet is 245 s. When the superheat is 20 K, the proportion of the equiaxed crystal region is higher—the highest value is 53.35%—and the average grain radius is 0.84556 mm. The proportion of the equiaxed crystal region decreases with the increase of superheat. When the superheat is 60 K, the proportion of the equiaxed crystal region is the lowest—the lowest value is 46.27%—and the average grain radius is 1.07653 mm. Proper reduction of superheat can obviously reduce the size of equiaxed crystal, expand the area of equiaxed crystal and improve the quality of casting billet.

Electromagnetic stirring (M-EMS) has been extensively applied in continuous casting production to reduce the quality defects of casting billets. To investigate the effect of continuous casting electromagnetic stirring on billet segregation, a 3D multi-physics coupling model was established to simulate the internal heat, momentum, and solute transfer behavior, to identify the effect of M-EMS on the carbon segregation of a continuous casting square billet of 200 mm × 200 mm. The results show that M-EMS can move the high-temperature zone upward, which is favorable for the rapid solidification of the billet, and can promote the rotational flow of the molten steel in the horizontal direction. When the electromagnetic stirring current is varied in the range of 0–500 A, the degree of carbon segregation first decreases and then increases, with the best control of segregation at 300 A. In the frequency range of 3–5 Hz, the degree of carbon segregation degree increases with frequency. Meanwhile, the simulation and experimental results show that 3 Hz + 300 A is the best electromagnetic stirring parameter for improving the carbon segregation of casting billets with a size of 200 mm × 200 mm. So, a reasonable choice of the M-EMS parameters is crucial for the quality of the billet.

The quality of the bloom will be impacted by the non-metallic impurities in the molten steel in the tundish, which will reduce the plasticity and fatigue life of the steel. In this research, a mathematical model of a six-flow double-channel T-shaped induction heating tundish was established, the effects of induction heating conditions on the removal of inclusions in the tundish were investigated, and the impact of various inclusion particle sizes on the removal effect of inclusions under induction heating was explored. The results show that the Residence Time Distribution (RTD) curve produced through numerical simulation and physical simulation is in good agreement. The reduction of inclusion particles in the channel is made affordable by the dual-channel induction heating technique. As the diameter of inclusion particles increases from 10 μm to 50 μm, the probability of inclusion particles being removed from the channel gradually decreases from 70.9% to 56.1%.

Carbon segregation is the major and classical internal defect in the continuous casting process of carbon steel. Based on the combined electromagnetic stirring equipment for new billet in a steel plant, China, the influence of combined electromagnetic stirring (M-EMS + F-EMS) on the carbon segregation of 300 mm × 340 mm special-shaped billet was studied via numerical simulation and on-site industrialization tests. The Lorentz force and carbon solute distribution were simulated under different EMS parameters. The formation mechanism of the carbon segregation of medium carbon steel with different combined electromagnetic stirring processes was analyzed. The results show that: (1) with the combined action of “solute flushing” effect and gravity, the carbon concentration in the loose side of the medium carbon steel casting billet is gradually lower than the fixed side, while the carbon concentration on the fixed side gradually accumulates more; and (2) under the action of combined electromagnetic stirring, the segregation index of casting billet could be controlled to remain between 0.96–1.05 and shows an increasing change in solidification from the skin to the center. When the current and frequency of M-EMS are 250 A and 2.0 Hz and the F-EMS are 180 A and 8.0 Hz, the carbon segregation defects in the special-shaped (300 mm × 340 mm) casting billet can be significantly improved.

In this study, a three-dimensional segmented coupled model for continuous casting billets under combined mold and final electromagnetic stirring (M-EMS, F-EMS) was developed. The model was verified by comparing carbon segregation in billets with and without EMS through plant experiments. The findings revealed that both M-EMS and F-EMS induce tangential flow in molten steel, impacting solidification and solute distribution processes within the billet. For M-EMS, with operating parameters of 250A-2Hz, the maximum tangential velocity (velocity projected onto the cross-section) was observed at the liquid phase’s edge. For F-EMS, with operating parameters of 250A-6Hz, the maximum tangential velocity occurred at $f_l=0.7$. Furthermore, F-EMS accelerated heat transfer in the liquid phase, reducing the central liquid fraction from 0.93 to 0.85. M-EMS intensified the washing effect of molten steel on the solidification front, resulting in the formation of negative segregation within the mold. F-EMS significantly improved the centerline segregation issue, reducing carbon segregation from 1.15 to 1.02. Experimental and simulation results, with and without EMS, were in good agreement, indicating that M+F-EMS leads to a more uniform solute distribution within the billet, with a pronounced improvement in centerline segregation.