Pre-chamber jet ignition is a promising way to improve fuel consumption of gasoline engine. A small volume passive pre-chamber was tested at a 1.5L turbocharged GDI engine. Combustion and emission characteristics of passive pre-chamber at low-speed WOT and part load were studied. Besides, the combustion stability of the passive pre-chamber at idle operation has also been studied. The results show that at 1500 r/min WOT, compared with the traditional spark ignition, the combustion phase of pre-chamber is advanced by 7.1°CA, the effective fuel consumption is reduced by 24 g/kW h, and the maximum pressure rise rate is increased by 0.09 MPa/°CA. The knock tendency can be relieved by pre-chamber ignition. At part load of 2000 r/min, pre-chamber ignition can enhance the combustion process and improve the combustion stability. The fuel consumption of pre-chamber ignition increases slightly at low load, but decreases significantly at high load. Compared with the traditional spark ignition, the NO_x emissions of pre-chamber increase significantly, with a maximum increase of about 15%; the HC emissions decrease, and the highest decrease is about 36%. But there is no significant difference in CO emissions between pre-chamber ignition and spark plug ignition. The intake valve opening timing has a significant influence on the pre-chamber combustion stability at idle operation. With the delay of the pre-chamber intake valve opening timing, the CoV is reduced and can be kept within the CoV limit.

Hydrogen is an ideal alternative fuel for internal combustion engines due to its fast combustion rate and near-zero carbon emissions. To further investigate the impact of the injection strategy on combustion performance under various excess air coefficients and loads, experimental methods were employed to systematically study injection timing, injection pressure, and dual injection. The results demonstrate that appropriately delaying hydrogen injection timing can improve the thermal efficiency by up to 2.6% and reduce NOx emissions of equivalent combustion by nearly 88%. While increasing the hydrogen pressure to 8 MPa does not directly enhance the thermal efficiency and emissions, it can reduce the injection pulse width by approximately 75%, allowing for more flexibility in delaying the injection timing. Delaying the secondary end of injection (SEOI) leads to a reduction of over 47% in NOx emissions for λ (excess air coefficient) values of 1.5 and 1.0. The combustion duration and ignition delay initially increase and then decrease with the delay in SEOI, depending on the movement state of the fuel jet. With the increase in secondary injection proportion (SIP), brake thermal efficiency increases by no more than 1%, but NOx is reduced by more than 43% for λ values of 1.5 and 1.0. In the case of ultralean conditions (λ = 2.3), increasing the SIP from 0 to 30% results in a nearly 14% increase in the peak heat release rate (HRR) and a 19% reduction in combustion duration.

In this paper, the optical and electronic properties of WSSe/BSe heterostructure are investigated by first-principles calculations. The most stable stacking pattern of the WSSe/BSe compounds is formed by van der Waals interaction with a thermal stability proved by ab initio molecular dynamics simulation. The WSSe/BSe heterostructure exhibits a type-I band alignment with direct bandgap of 2.151 eV, which can improve the effective recombination of photoexcited holes and electrons. Furthermore, the band alignment of the WSSe/BSe heterostructure can straddle the water redox potential at pH 0–8, and it has a wide absorption range for visible light. In particular, the solar-to-hydrogen efficiency of the WSSe/BSe heterostructure is obtained at as high as 44.9% at pH 4 and 5. All these investigations show that the WSSe/BSe heterostructure has potential application in photocatalysts to decompose water.

Recently, the energy shortage has become increasingly prominent, and hydrogen (H₂) energy has attracted extensive attention as a clean resource. Two-dimensional (2D) materials show excellent physical and chemical properties, which demonstrates considerable advantages in the application of photocatalysis compared with traditional materials. In this investigation, based on first-principles methods, 2D PtS₂ and MoTe₂ are selected to combine a heterostructure using van der Waals (vdW) forces, which suggests a type-II band structure to prevent the recombination of the photogenerated charges. Then, the calculated band edge positions reveal the decent ability to develop the redox reaction for water splitting at pH 0. Besides, the potential drop between the PtS₂/MoTe₂ vdW heterostructure interface also can separate the photogenerated electrons and holes induced by the charge density difference of the PtS₂ and MoTe₂ layers. Moreover, the fantastic optical performances of the PtS₂/MoTe₂ vdW heterostructure further explain the promising advanced usage for photocatalytic decomposition of water.

Using hydrogen and its compounds as fuel is one of the key ways to achieve zero carbon emissions in internal combustion engines. Due to the difference in fuel properties of hydrogen and ammonia, mixing the two can make up for each other's shortcomings in combustion performance. Therefore, this paper studies the effects of ammonia addition on the combustion and emission characteristics of a SI commercial hydrogen engine, and studies the differences in these effects under different excess air ratios. The results indicate that increasing the ammonia mass ratio lengthens both flame development and combustion duration, causing a delay in the combustion center. Under stoichiometric conditions, combustion instability increases, peak cylinder pressure and heat release rate decrease significantly, and exhaust temperatures rise. With a higher ammonia mass ratio, brake-specific fuel consumption first decreases and then increases, reaching a minimum at a 0.4-0.6 ammonia mass ratio. Unburned ammonia and N₂O emissions gradually increase, while NO _X emissions initially rise and then fall, peaking at a low ammonia mass ratio. From the perspective of balancing emissions and fuel economy, for hydrogen-ammonia mixed combustion engines, a 0.6 ammonia mass ratio is recommended under stoichiometric conditions, while lean burn conditions allow for a higher ammonia mass ratio.

The combustion and emission characteristics of a hydrogen engine were investigated through experimental analysis using a GDI engine. To enable hydrogen in-cylinder direct injection, a specialized hydrogen gas injector was employed. A comparative analysis of the combustion performance between gasoline and hydrogen fuels in a spark-ignited engine was conducted. Additionally, the study experimentally explored the thermal efficiency and emission reduction potential of hydrogen engines in lean combustion modes. The results indicated a significant improvement in the combustion rate when hydrogen fuel was utilized in the spark-ignited engine. However, the effective thermal efficiency was found to be lower than that of gasoline fuel due to the delayed MBF50 under stoichiometric conditions. Furthermore, when compared to gasoline fuel, the reduction of CO and THC emissions was accompanied by an increase in NOx emissions. Nevertheless, optimizing the air dilution ratio in hydrogen engines led to an improvement in the effective thermal efficiency. Specifically, under medium load conditions, a Lambda value of 2.7 resulted in an effective thermal efficiency of 43.5%. Additionally, under ultra-lean conditions (Lambda > 2.3), NOx emissions could be reduced to below 50 ppm, reaching as low as 44 ppm. This study highlights the potential of improving combustion efficiency and reducing emissions by utilizing hydrogen fuel, particularly in lean combustion modes. It contributes to the continuous development of hydrogen engine technology and promotes the implementation of cleaner and more efficient energy solutions.