Budi Azhari

Mr. Budi Azhari

Indonesian Institute of Sciences (LIPI)
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 May 2024 in Polymer International
Verified
Journal Article
Closed access
SUSuprapto
Suprapto
YTYung Ting
Yung Ting
Hariyanto GunawanHariyanto Gunawan
Hariyanto Gunawan
EYEdwar Yazid
Edwar Yazid
ANAditya Sukma Nugraha
Aditya Sukma Nugraha
JUJubaidah
Jubaidah

18 August 2021 in Energies
Verified
Journal Article
Open access
PDF file
Budi AzhariBudi Azhari
Budi Azhari
Fransisco Danang WijayaFransisco Danang Wijaya
Fransisco Danang Wijaya
EYEdwar Yazid
Edwar Yazid
For generating electricity, direct-drive wave energy converters (WECs) with linear permanent magnet generators (LPMGs) have advantages in terms of efficiency, simplicity, and force-to-weight ratio over WEC with rotary generators. However, the converter’s work under approaching-real wave conditions should be investigated. This paper studies the performance of a pico-scale WEC with two different LPMGs under unidirectional long-crested random waves. Different significant wave heights (using data in the Southern Ocean of Yogyakarta, Indonesia) and peak frequencies are tested. The JONSWAP energy spectrum is used to extract the wave elevations, while the MSS toolbox in MATLAB Simulink is employed to solve the floater’s dynamic responses. Next, the translator movements are extracted and combined with the flux distribution from FEMM simulation and analytical calculation, and the output powers are obtained. An experiment is conducted to test the output under constant speed. The results show for both designs, different tested significant wave height values produce higher output powers than peak frequency variation, but there is no specific trend on them. Meanwhile, the peak frequency is inversely proportional to the output power. Elimination of the non-facing events results in increasing output power under both parameters’ variation, with higher significant wave height resulting in a bigger increase. The semi iron-cored LPMG produces lower power loss and higher efficiency.

1 January 2016
Verified
Conference Paper
Closed access
Budi AzhariBudi Azhari
Budi Azhari
FWFransisco Danang Wijaya
Fransisco Danang Wijaya
WPWassy Prawinnetou
Wassy Prawinnetou
HAH. Dewangga Adhyaksa
H. Dewangga Adhyaksa
In this paper, sea wave power plant was designed to be applied in southern coast of Yogyakarta, Indonesia. The plant was expected to generate 700 Wp output. It had two components: tubular linear permanent magnet generator (TLPMG) and floater buoy. The buoy and the ocean wave were assumed moving continuously. By this condition, the generator was then simulated using finite element software of FEMM. Analytical calculation was performed later, which shows that the generator could generate induced voltage and output power up to 68.243 Vp and 674.811 Wp respectively. Furthermore, the generator only generated power at certain times, due to different length between the wave magnitude and translation path of the translator.

1 December 2016 in International Journal of Electrical and Computer Engineering (IJECE)
Verified
Journal Article
Open access
PDF file
FWFransisco Danang Wijaya
Fransisco Danang Wijaya
Budi AzhariBudi Azhari
Budi Azhari
HSHarnoko Stephanus
Harnoko Stephanus
Flat-quasi type of linear permanent magnet generators (LPMGs) have been considered to be applied for several applications, such for wave energy conversion and free piston combustion engine. One of the important issues concerning LPMG is the permanent magnets configuration, due to its effects to the generator’s excitation performance. In this paper, a 1 kW flat-quasi LPMG would be designed and built. During the process, optimum permanent magnets configuration was required and researched. The optimum configuration considered the output power and resulted cogging force. Invetigation was then conducted by modifying several variables, including poles’ arrangement, pole length, number of pole, and pole skewing angle. The modification constraints were total permanent magnets’ volume and generator dimension. The results showed that permanent magnet configuration with halbach arrangement, pole length equals 55% of the slot pitch length, and 61.19o skewing angle produced the optimum output values.

1 January 2017 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
Budi AzhariBudi Azhari
Budi Azhari
WPWassy Prawinnetou
Wassy Prawinnetou
DHDewangga Adhyaksa Hutama
Dewangga Adhyaksa Hutama
Indonesia has several potential ocean energies to utilize. One of them is tidal wave energy, which the potential is about 49 GW. To convert the tidal wave energy to electricity, linear permanent magnet generator (LPMG) is considered as the best appliance. In this paper, a pico-scale tidal wave power converter was designed using quasi-flat LPMG. The generator was meant to be applied in southern coast of Yogyakarta, Indonesia and was expected to generate 1 kW output. First, a quasi-flat LPMG was designed based on the expected output power and the wave characteristic at the placement site. The design was then simulated using finite element software of FEMM. Finally, the output values were calculated and the output characteristics were analyzed. The results showed that the designed power plant was able to produce output power of 725.78 Wp for each phase, with electrical efficiency of 64.5%. The output characteristics of the LPMG: output power would increase as the average wave height or wave period increases. Besides, the efficiency would increase if the external load resistance increases. Meanwhile the output power of the generator would be maximum at load resistance equals 11 Ω.

1 October 2016
Verified
Conference Paper
Closed access
FWFransisco Danang Wijaya
Fransisco Danang Wijaya
Budi AzhariBudi Azhari
Budi Azhari
This paper aimed to find out a model of 1 kWp flat-quasi linear permanent magnet generator (LPMG) for ocean wave power plant in South Java Ocean. First, a flat-quasi LPMG is modeled based on the wave characteristic at the placement site. The model was then simulated using finite element software of FEMM 4.2. Next, the model was optimized to find out the optimum output power and cogging force. The optimization was performed by modifying pole's length and number but constant total translator length. The optimized model could generate up to 1,424.65 Wp (6% higher output power), with 38.85% lower cogging force than the initial model. The output power was maximum when the load resistance equals 1 Ω. Based on the configuration of the LPMG and wave characteristic, the generator generates power only in certain time. This is due to different size between the wave amplitude and the translation path length. Moreover, the average wave height would be directly proportional to the translation speed, induced voltage, and output power.