Sang-Hye Lee

Ms. Sang-Hye Lee

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2021 in Crystals
Verified
Journal Article
Open access
PDF file
SLSang-Min Lee
Sang-Min Lee
SLSang-Hye Lee
Sang-Hye Lee
JRJae-Seung Roh
Jae-Seung Roh
In the present study, carbon black activated by CO2 gas was examined through XRD analysis, especially with regard to changes in its structural parameters. Based on the results, its activation process was thoroughly analyzed. The activation process was controlled by isothermally activating the carbon black inside a reaction tube through which CO2 gas flowed. With this approach, the degree of activation was varied as desired. At an early stage of the activation process, the amorphous fraction on the carbon black surface was preferentially activated, and later the less-developed crystalline carbon (LDCC) region inside the carbon black particles started to be activated. The latter process was attributable to the formation of pores inside the carbon black particles. As the activation process proceeded further, the more-developed crystalline carbon (MDCC) region started to be activated, thereby causing the pores inside the carbon black particles to grow larger. At the last stage of the activation process, La was found to be decreased to about 40 Å. This implied that the edges of the graphite crystals had been activated, thus causing the internal pores to grow and coalesce into larger pores. Activated conductive Super-P with enhanced pore properties is expected to have wide applications.

1 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
SLSang-Hye Lee
Sang-Hye Lee
JKJae-Hyun Kim
Jae-Hyun Kim
WKWoo-Seok Kim
Woo-Seok Kim
JRJae-Seung Roh
Jae-Seung Roh
In the present study, graphite blocks were fabricated using synthetic graphite scrap and phenolic resin, and the effect of the heating rate during carbonization on their mechanical and electrical characteristics was examined. While varying the heating rate from 1, 3, 5, and 7 to 9 °C/min, the microstructure, density, porosity, flexural strength, compressive strength, and electrical resistivity of the fabricated graphite blocks were measured. As the heating rate increased, the pores in the graphite blocks increased in size, and the shape of the gas release paths became more irregular. Overall, it was found that increases in the heating rate led to the degradation of the graphite blocks’ mechanical and electrical properties.

26 January 2024 in Crystals
Verified
Journal Article
Open access
PDF file
SLSang-Hye Lee
Sang-Hye Lee
JRJae-Seung Roh
Jae-Seung Roh
In this study, changes in the microstructure of coal-tar pitch (CTP) during successive processes, including pyrolysis, polycondensation, and crystallization, were examined in connection with the resulting variations in structure factors, as measured by X-ray diffraction (XRD) analysis, and functional groups, as confirmed by Fourier transform infrared (FTIR) spectroscopy. To this end, four zones were defined based on variations in crystallinity, which were indicated by d002 and Lc. Each zone was further characterized by interpreting crystallinity development in relation to changes in functional groups and specimen height. At around 400 °C, polycondensation occurred as the C-Har and C-Hal peaks decreased in intensity. These peak reductions coincided with the formation of mesophase spheres, resulting in enhanced crystallinity. Subsequently, at around 500 °C, the peak intensity of C-H and COOH decreased, which was attributed to the release of large amounts of gases. This led to sharp volume changes and a temporary reduction in crystallinity. All these results suggest that changes in the functional groups of CTP at lower temperatures (600 °C or less) during the carbonization process are closely associated with variations in its crystallinity. The major findings of the present study provide valuable insights for designing highly effective processes in the manufacturing of synthetic graphite blocks using CTP as a binder material, including by selecting appropriate temperature ranges to minimize volume expansion and crystallinity degradation and determining the lowest possible carbonization temperature to ensure adequate binder strength.

5 May 2023 in Materials
Verified
Journal Article
Open access
PDF file
JKJong-Hwan Ko
Jong-Hwan Ko
SLSang-Hye Lee
Sang-Hye Lee
JRJae-Seung Roh
Jae-Seung Roh
The purpose of this study is to improve the oxidation resistance of graphite blocks after graphitization at 2800 °C by introducing a curing process of phenolic resin, used as a binder to control the pore size. Using the methylene index obtained from FTIR, the curing temperature was set to 150 °C, the temperature at which cross-linking most highly occurs. Graphite blocks that had undergone curing, and were carbonized with a slow heating rate, showed increased mechanical and electrical properties. Microstructural observation confirmed that the curing process inhibited the formation of large pores in the graphite block. Therefore, the cured graphite block showed better oxidation resistance in air than a non-cured graphite block. Oxidation of the graphite block was caused by pores created by pyrolysis of the phenolic resin binder, which acted as active sites.

20 August 2021 in Materials
Verified
Journal Article
Open access
PDF file
SLSang-Hye Lee
Sang-Hye Lee
SLSang-Min Lee
Sang-Min Lee
JRJae-Seung Roh
Jae-Seung Roh
Milled polyacrylonitrile (PAN)-based Carbon Fibers (mPCFs) were prepared from PAN-based carbon fibers by using a ball milling process. The resulting structural changes in the mPCFs were analyzed by correlating the analytical results obtained by X-ray diffraction (XRD) and Raman spectroscopy and verified by transmission electron microscopy (TEM) lattice images and diffraction patterns. The crystallite size La calculated from the XRD measurements decreased as the milling time was increased to 12 h and then decreased as the milling time was further increased to 18 h. The La of both partially-milled Carbon Fiber (pmCF) and milled Carbon Fiber (mCF) calculated from the Raman spectroscopy data continuously increased as the milling time increased. The difference may be because XRD measured the entire sample regardless of pmCF and mCF, while Raman spectroscopy was limited to measuring the surface and differentiated pmCF and mCF. As the ball milling time increased, the fiber surface was firstly broken by the impact energy of the balls, decreasing crystallinity, while the La inside the unbroken fibers increased.

16 January 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SGSun-Ung Gwon
Sun-Ung Gwon
SLSang-Hye Lee
Sang-Hye Lee
UYU-Sang Youn
U-Sang Youn
JRJae-Seung Roh
Jae-Seung Roh
In this study, isotropic coke and coal tar pitch were subjected to compression molding while varying the compression pressure and holding time. As a result, carbon blocks were fabricated, and their mechanical properties and microstructure were analyzed, with respect to applied pressure and holding time. The compression pressure was set to 70, 100 and 130 MPa, while the holding time was set to 1, 2 and 3 min. Overall, with an increase in compression pressure, bulk density increased while porosity decreased. Increased compression pressure also led to enhanced mechanical and electrical properties. Microstructural analysis confirmed that, after compression molding granules that were larger than existing kneaded particles appeared. The formation of granules is attributed to the tendency of kneaded particles to connect and coalesce with each other under applied pressure during the compression molding process. As the compression pressure increased, the proportion of granules in the microstructure increased while the size of pores decreased. This phenomenon can be attributed to kneaded particles coming closer to each other under applied pressure. At a compression pressure of 130 MPa, both bulk density and porosity increased with a longer holding time. Some pores existed within granules, while others protruded out of granules, thereby forming long channels of connected pores around them. This microstructural change was considered to result in degraded mechanical and electrical properties.