A methane/oxygen mixture is considered to be an appropriate propellant for many future rocket engines due to its practicality and low cost. To better understand the combustion instability in methane/oxygen-fed rocket engines, the spontaneous transverse combustion instability in a rectangular multi-element combustor (RMC) was analyzed both experimentally and numerically. Severe combustion instabilities occurred in the RMC during repeatable hot-fire tests. The physical mechanisms were systematically investigated through numerical simulations based on the stress-blended eddy simulation and flamelet-generated manifolds method with detailed chemical mechanisms (GRI Mech 3.0). The numerical results for the frequency spectrum and spatial modes agree well with the theoretical analysis and experimental data. The driven regions of the combustion instability were identified on both sides of the combustion chamber through a Rayleigh index analysis. The longitudinal pressure oscillations in the oxidizer post were found to be coupled with the transverse pressure waves in the combustion chamber and led to periodic oscillations of the mass flow rate of propellant. Moreover, the mixing was highly enhanced when the pressure wave interacted with walls of the combustion chamber. Therefore, a sudden release of heat occurred. The pressure oscillations were enhanced by pulsated heat release. A closed-loop system with positive feedback associated with periodic oscillations mass flow rate of the propellant, and sudden heat release, was believed to account for the present combustion instability.
Self-excited combustion instabilities of transverse modes were experimentally investigated in a rectangular multi-injector model combustor, operating with the bipropellants O2/CH4. The propellants were injected through a linear array of five oxidizer-centered shear coaxial injectors into the combustor. High-amplitude limit cycles obtained in hot-fire tests were analyzed in detail. Different combustion instability modes, including first and second width modes, were observed in cases with three different injection distribution schemes. Hence, the injection distribution strongly determined the combustion dynamics. One insight can be gained that the stable combustion could be achieved by properly designing the propellants' injection distributions.
Effects of secondary gas injection on flame shape and combustion stability of a premixed swirl methane/air flame were investigated experimentally. Without secondary gas injection, an attached M-shaped flame was observed with pressure oscillations up to a sound pressure level of 68 dB. The flame exhibited significant oscillations due to flame–vortex interactions induced by velocity fluctuations. The secondary methane or air was separately injected into the outer recirculation zone to suppress the flame oscillations at a volume flow rate of 0.5% of the primary flow rates. For lower primary air flow rates (Qair ≤ 60 L/min), both secondary methane and air injections were able to suppress the thermoacoustic instability and performed the sound pressure level reduction of 45 dB. Meanwhile, the flame transformed from an attached unstable M-shaped flame to a detached stable V-shaped flame. The secondary methane or air injection served to stabilize the flame and anchor its spatial heat release distribution by limiting the variation of flame shape in the outer recirculation zone, suppressing thermoacoustic oscillation. For higher primary air flow rates (Qair = 80 L/min), the secondary methane injection could reduce sound pressure levels to noise levels, while secondary air injection could not. The velocity disturbances and heat release fluctuations introduced by secondary methane injection could lead to a transformation in flame shape and achieve the suppression of thermoacoustic oscillation. However, the velocity disturbances induced by secondary air injection were insufficient to stabilize the flame.
Thermoacoustic instability (TAI) presents a critical challenge for lean-burning combustors and rocket engines. The early detection of instability is crucial, and to address this, a data-driven prediction framework has been established for TAI in a sub-scale rocket combustor with variable chamber length. Nonlinear combustion features are generated from time series of dynamic pressure using recurrence matrices. Deep learning models are then utilized to train these features and predict the proximity of impending TAI. The performance of the proposed method is investigated through cross-validations of 12 groups of hot-fire test datasets. Remarkably, the prediction performances are in good agreement with measured experimental data, with most instabilities being predicted dozens of milliseconds in advance. This capability paves the way for the early implementation of active control systems in full-scale combustors in the future. The prediction performances are also compared with state-of-the-art TAI prediction methods.