Sungchul Chun

Prof. Sungchul Chun


Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 August 2017 in Materials
Verified
Journal Article
Open access
PDF file
Yeonung JeongYeonung Jeong
Yeonung Jeong
Craig HargisCraig Hargis
Craig Hargis
SCSungchul Chun
Sungchul Chun
JMJuhyuk Moon
Juhyuk Moon
This study investigated the hydration characteristics and strength development of calcium sulfoaluminate-belite (CSAB) cements incorporating calcium carbonate (CC) powders with various particle size distributions and different gypsum amounts. In general, the CSAB hydration was accelerated by the CC powder, but the acceleration and resulting strength improvement were more effective with finer CC powder. Regardless of the fineness of the CC powder, it took part in the hydration of CSAB cement, forming hemicarboaluminate and monocarboaluminate phases. These hydration and nucleation effects compensated for the strength reduction from decreased cementing components (i.e., dilution effect) when finer CC powders were used, while they did not overcome the strength reduction when coarser CC powder was used. On the other hand, increasing the amount of gypsum for a given CC content improved the strength. The strength of CSAB cement had a clear inverse relationship with its total pore volume measured by mercury intrusion porosimetry (MIP). Thermodynamic modeling for CSAB cement hydration showed that the use of CC powder increased total volume of solid phases up to 6 wt % at a given amount of gypsum.

1 January 2007 in ACI Structural Journal
Verified
Journal Article
Closed access
PDF file
SCSungchul Chun
Sungchul Chun
SLSung Ho Lee
Sung Ho Lee
TKThomas H.-K. Kang
Thomas H.-K. Kang
BOBohwan Oh
Bohwan Oh
JWJohn W. Wallace
John W. Wallace

1 September 2009 in ACI Structural Journal
Verified
Journal Article
Closed access
PDF file
SCSungchul Chun
Sungchul Chun
BOBohwan Oh
Bohwan Oh
SLSungho Lee
Sungho Lee
CNClay J. Naito
Clay J. Naito

1 May 2017 in Magazine of Concrete Research
Verified
Journal Article
Closed access
SCSungchul Chun
Sungchul Chun
To investigate the development of compression splice resistances, compression splices under normal conditions, splices with bond only and splices with bearing only were tested. The bond and bearing strengths of the normal splices were found to be less than those of splices with bond only and splices with bearing only, respectively, because in the normal splices the circumferential tensile stresses induced by bearing and bond overlapped at the ends of the splice length. However, the strengths of the normal splices are always higher than the strengths of the bond only or bearing only splices because the normal splices exhibit less slip compared to the bond only or bearing only splices at the same level of bar stress. Consequently, the splice strength in compression cannot be improved by removing either the bond or the bearing. In addition, the bond strength in the bond only splices is nearly the same as the bond strength in tension splices.

1 March 2010 in ACI Structural Journal
Verified
Journal Article
Closed access
PDF file
SCSungchul Chun
Sungchul Chun
SLSungho Lee
Sungho Lee
BOBohwan Oh
Bohwan Oh

1 February 2023 in Journal of Structural Engineering
Verified
Journal Article
Closed access
PDF file
HSHye-Jung Sim
Hye-Jung Sim
SCSungchul Chun
Sungchul Chun
IKIn-Ho Kim
In-Ho Kim
Due to a lack of test data on large-diameter headed bars, design provisions limit the bar diameter of headed bars to 36 mm or less. In exterior beam–column joints with two-layer headed bars as beam bars, if the layer-to-layer spacing of the headed bars is narrow, the side-face blowout area of an individual headed bar is overlapped. Existing design provisions do not consider the effects of layer-to-layer spacing. In this study, 34 simulated exterior beam–column joints were tested to examine the effects of bar diameters over the limitation of existing design provisions using large-diameter (41- and 51-mm) headed bars. The side-face blowout strengths of the two-layer headed bars were experimentally investigated through simulated exterior beam–column joints with layer-to-layer spacing of 2db (two times the bar diameter). The test results showed that the side-face blowout strengths had the same characteristics for bar diameters from 22 to 51 mm. For the two-layer headed bars, crack propagation and failure mode were the same as those for single-layer headed bars, but due to the overlap of the blowout area, the strength of the individual headed bar was reduced. A new model was proposed to predict the side-face blowout strengths of large-diameter high-strength headed bars in both a single layer and in two layers by incorporating a spacing factor for an individual headed bar into a model from the literature. A total of 173 test results from this study and previous studies were compared with predictions from the proposed model, and the average and coefficient of variation (COV) of test-to-prediction ratios were 1.08 and 17.4 %, respectively.