Graphite waste from primary batteries, active yeast and commercial rice husk ash have been used as pore-forming agents to fabricate porous alumina ceramics using a fugitive materials technique. The pore-forming agent ratios were between 10 to 50 wt %. The effects of the pore-forming agent ratios on the mechanical properties, the porosity and the microstructure have been investigated in this study. The results showed that through increasing the pore-forming agent ratio for graphite waste, yeast and rice husk ash, the porosity increased from 37.3 to 61.1%, 30.2 to 63.8% and 42.9 to 49.0%, respectively. The hardness also decreased from 172.6 to 38.1 HV 1 and from 160.6 to 15.0 HV 1 for porous alumina ceramics using graphite waste and yeast as pore-forming agents, respectively. However, the hardness of the porous alumina ceramics with rice husk ash as a pore-forming agent increased at 30 wt % (150.9 HV 1) and 50 wt % (158.9 HV 1). The tensile strength for porous alumina ceramics using graphite waste and yeast as pore-forming agents decreased from 24.9 to 14.3 MPa and from 26.2 to 5.4 MPa. The compressive strength decreased from 112.3 to 34.3 MPa and from 19.5 to 1.8 MPa, respectively. However, for porous alumina ceramics using rice husk ash, the tensile strength increased at 30 wt % (24.1 MPa) and 50 wt % (21.9 MPa). The compressive strength also increased at 30 wt % (69.7 MPa) and at 50% (60.1 MPa).
1 January 2017 in Advances in Materials Science and Engineering
A porous ceramic is made from composite materials which consist of alumina and commercial rice husk ash. This type of ceramics is obtained by mixing the commercial rice husk ash as a source of silica (SiO2) and a pore forming agent with alumina (Al2O3) powder. To obtain this type of ceramic, a solid-state technique is used with sintering at high temperature. This study also investigated the effects of the rice husk ash ratios on the mechanical properties, porosity, and microstructure. The results showed that, by increasing the content of the rice husk ash from 10 to 50 wt%, there is an increase in the porosity from 42.92% to 49.04%, while the mechanical properties decreased initially followed by an increase at 30 wt% and 50 wt%; the hardness at 20 wt% of the ash content was recorded at 101.90 HV1. When the ash content was increased to 30 wt% and 50 wt%, the hardness was raised to 150.92 HV1and 158.93 HV1, respectively. The findings also revealed that the tensile and compressive strengths experienced a decrease at 10 wt% of the ash content and after that increase at 30 wt% and 50 wt% of rice husk ash. XRD analysis found multiple phases of ceramic formation after sintering for the different rice husk ash content.
1 February 2021 in IOP Conference Series: Materials Science and Engineering
Recent developments in the materials science field have highlighted the need for further composite materials study, especially with regard to bio and nano-composites, as their abilities to meet modern requirements with regard to facilitating technological advancement is far greater than those of monolithic materials. There are several advantages to nano and bio-composites as compared to conventional materials, including properties such as fatigue resistance, impact resistance, stiffness, corrosion resistance, biodegradability, thermal conductivity, low relative density, environmentally friendly waste stages, and high specific strength. Recent years have seen the discovery of several new high-performing composite materials, and improvements in the fields of aviation, automobile, adhesion, building, and electronic engineering also support the adoption of more general utilisation of nano and bio-composites in a much wider range of applications than those for which they were originally designed. This paper thus highlights and reviews information on bio- and nano-composite materials to determine current trends in how these materials are used in the various fields of engineering in numerous applications, and to examine the role of nanotechnology in the enhancement of composite properties.
13 July 2017 in Journal of the Australian Ceramic Society
The main goal of this study is to determine the effect of the addition of Cu metal of nanoscale particle on the mechanical properties and porosity of porous alumina ceramics. Porous alumina reinforced ceramics were prepared using nanoscale Cu metal particles as their strengthening phase. Solid state and sacrificial techniques were used to prepare the porous alumina reinforced ceramics. A FESEM was used to analyse the microstructure. Different ratios of Cu metal were added (3 wt%, 6 wt%, 9 wt% and 12 wt% Cu) at different ratios of yeast used as a pore agent. The results indicated that with increasing the ratios of Cu metal, the porosity decreased and the mechanical properties increased. The increase in the mechanical properties could be attributed to the decrease in the porosity and the toughening mechanism of porous alumina ceramics. Some potential applications include, filtration, thermal and purging of gas.