Ko Ikeda

Prof. Ko Ikeda


Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 July 2016 in Materials
Verified
Journal Article
Open access
PDF file
ZLZhuguo Li
Zhuguo Li
TOToshihiko Ohnuki
Toshihiko Ohnuki
KIKo Ikeda
Ko Ikeda
Ambient temperature geopolymerization of paper sludge ashes (PS-ashes) discharged from paper mills was studied by means of scanning electron microscopy (SEM), X-ray diffraction (XRD), induction coupled plasma atomic emission spectrometry (ICP-AES), and X-ray absorption near edge structure (XANES). Two varieties of alkaline liquors were used in the PS-ash based geopolymers, corresponding to aqueous Na-metasilicate and Na-disilicate compositions. PS-ashes were found to be semi-crystalline and to have porous structures that make it possible to absorb much liquor. Flexural strengths of PS-ash-based geopolymers with liquor/filler ratios (L/F) of 1.0–1.5 ranged from 0.82 to 1.51 MPa at 4 weeks age, depending on PS-ashes and liquors used. The reaction process of the constituent minerals of the PS-ash is discussed. Furthermore, we attempted to solidify hazardous water contaminated with radioisotopes. Non-radioactive strontium and cesium nitrates were added as surrogates at a dosage of 1% into the PS-ash-based geopolymers. Generally, high immobilization ratios up to 99.89% and 98.77% were achieved for Sr2+ and Cs+, respectively, depending on the source of PS-ashes, alkaline liquors, and material ages. However, in some cases, poor immobilization ratios were encountered, and we further discussed the causes of the instability of derived geopolymer gels on the basis of XANES spectra.

25 March 2024 in Materials
Verified
Journal Article
Open access
PDF file
ZLZhuguo Li
Zhuguo Li
KIKo Ikeda
Ko Ikeda
It is thought that geopolymers are easy to carbonate, especially when they are cured in ambient temperatures. Matrix gel’s composition and microstructure, and new products of geopolymers (GPs) after carbonation were investigated in this study on the basis of XRD and SEM-EDS measurements and ternary diagram analysis, which were prepared from low-lime fly ash (FA) and ground granulated blast-furnace slag (GGBS) alone or a blend, as a precursor. The specimens were hardened in a 20 °C environment with alkali activator solution (S/N = 1.1 in mole), followed by storage under sealing or accelerated carbonation. XRD patterns show that carbonation products were nahcolite for the sole FA-based GP and calcite for the GPs using GGBS alone or as a blend. The SEM images of carbonated samples show that there were cube-shaped calcite and small calcite particles in the GGBS-based GP, but hail-like particles in the FA/GGBS blend-based GP. The hail-like particles were complexes of calcite and C-A-S-H gels determined by ternary diagram analysis, and were found to plug the top of the pores of the spongy C-A-S-H gels. We also confirmed that combined ternary diagram analysis of S-(C + M + N)-A and A-(C + M)-N are very effective in determining the gel type of a geopolymer, as well as the products and compositional changes after carbonation, in which oxide components of gels are determined by SEM-EDS. In the former diagram, C-A-S-H gels were plotted linearly along the (C + M + N)-albite (Ab) join, while N-A-S-H gels showed a scattered distribution. In the latter diagram, the plots for N-A-S-H and C-A-S-H gels are distributed in different zones. N = Na2O, C = CaO, M = MgO, A = Al2O3, S = SiO2, H = H2O.

1 July 2007 in Inorganic Materials
Verified
Journal Article
Closed access
PDF file
TTT. Terai
T. Terai
AMA. Mikuni
A. Mikuni
YNY. Nakamura
Y. Nakamura
KIKo Ikeda
Ko Ikeda
Synthesis of ettringite, Ca6Al2(OH)12(SO4)3·26H2O has been attempted in suspensions of portlandite, Ca(OH)2 under CO2-free condition, agitating by a magnetic stirrer for constant 3 h at room temperature. Al-sulfate hydrate, Al2(SO4)3·(14–18)H2O solution (0.01 M) was used for Al2O3 and SO3 sources and appropriate amount of portlandite was mixed with the solution together with sucrose for boosting portlandite dissolution. The Ca/Al atomic ratio in suspensions was varied from 1.0 to 5.0 at intervals of 0.5. Run products were collected by filtration and washing and air-dried and evaluated by XRD, XRF, and RF-SEM. No ettringite formed at Ca/Al = 1.0, but ettringite began to form at Ca/Al = 1.5 and over. Measurement of pH of supernatants indicated pH 9.86 as a critical point of ettringite formation, and this mineral was always identified in a pH region above this point. Minute crystallites of ettringite were obtained up to 2 μm. The Yield of ettringite was suspended around 95 wt% as dry-base even in stoichiometric mixing due to the presence of portlandite remaining undissolved as relicts. As a consequence, no marked difference of the yield was found among Ca/Al 2.0 to 3.5 runs. The remaining portlandite was apt to decompose into crystalline calcite during the air-dry process. However, formation of amorphous calcite was estimated in some runs during this decomposition process.

20 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
ZLZhuguo Li
Zhuguo Li
KIKo Ikeda
Ko Ikeda
In this paper, we distinguished the degradation of alkali-activated material (AAM) exposed to sulfuric acid as physical (scaling, spalling, cracking, breaking, etc.) and chemical degradation (neutralization), because the mechanisms of these two types of degradation are different. Then, the effects of curing method, raw materials, and their mixing proportions on the two kinds of degradation of AAMs containing GGBFS were investigated in detail, including liquid-filler ratio, component of alkali activator, chemical admixture, inactive filler alternative to fly ash (FA), addition of municipal waste incineration bottom ash (BA), etc. The experimental results show that (a) small liquid-filler ratio, heat-curing, and the use of blended alkali activator solution of sodium silicate and NaOH can reduce both physical and chemical degradation of AAMs; (b) large GGBFS content or AE agent addition decreases the physical degradation, but increases the chemical degradation; (c) using crushed stone powder to replace FA and adding BA or a retarder would increase the physical and chemical degradation; but (d) the use of drying shrinkage reducer composed of polyether derivatives does not affect acid resistance. We also discussed the applicability and limitation of XRD and SEM-EDS in analyzing the chemical compositions of Ca-rich AAMs exposed to sulfuric acid, and found that (e) XRD analysis can identify the gypsum formation, and the gypsum peak intensity is related to the physical degradation of the Ca-rich AAMs; (f) by SEM-EDS analysis, the decalcification and dealkalization of C-A-S-H gels can be judged from the decrease in the average Ca/Si atomic ratio and the average Na atomic percentage in the acid corrosion area, but dealumination can be only determined from the dissimilarity of Al and Si elemental maps; and (g) if the CaO/SO3 molar ratio ranges from 0.8 to 1.0, gypsum formation can be estimated.

24 August 2018 in Materials
Verified
Journal Article
Open access
PDF file
ZLZhuguo Li
Zhuguo Li
MNMariko Nagashima
Mariko Nagashima
KIKo Ikeda
Ko Ikeda
Long-term immobilization ratios of strontium (Sr2+) and cesium (Cs+) in paper sludge ash-based geopolymer (PS-GP) were investigated in one year. PS-GP paste specimens were prepared in the conditions of 20 °C and 100% R.H., using two kinds of paper sludge ash (PS-ash). Two kinds of alkaline solution were used in the PS-GP as activator. One was prepared by diluting aqueous Na-disilicate (water glass) with seawater. Another was a mixture of this solution and caustic soda of 10 M concentration. When seawater was mixed into the alkaline solution, unstable fixations of Sr2+ and Cs+ were greatly improved, resulting stable and high immobilization ratios at any age up to one year, no matter what kind of PS-ash and alkaline solution were used. Element maps obtained by EPMA exhibited nearly even distribution of Cs+. However Sr2+ was biased, making domains so firmly related to Ca2+ presence. The mechanism that seawater stabilizes immobilization of Sr2+ and Cs+ was discussed in this study, but still needs to further investigation. Chemical composition analyses of PS-GP were also conducted by SEM-EDS. Two categories of GP matrix were clearly observed, so called N-A-S-H and C-A-S-H gels, respectively. By plotting in ternary diagrams of SiO2-(CaO + Na2O)-Al2O3 and Al2O3-CaO-Na2O, compositional trends were discussed in view of ‘plagioclase gels’ newly found in this study. As a result, it is suggested that the N-A-S-H and C-A-S-H gels should be strictly called Na-rich N-C-A-S-H and Ca-rich N-C-A-S-H gels, respectively.

23 October 2024 in Materials
Verified
Journal Article
Open access
PDF file
KIKazuo Ichimiya
Kazuo Ichimiya
RYRieru Yamamoto
Rieru Yamamoto
KIKo Ikeda
Ko Ikeda
QNQuang Dieu Nguyen
Quang Dieu Nguyen
ACArnaud Castel
Arnaud Castel
The widespread adoption of geopolymer concretes in the industry has been slow, mainly due to concerns over their long-term performance and durability. One of the main causes of concrete structures’ deterioration is chloride-induced corrosion of the reinforcement. The reinforcement corrosion process in concrete is composed of two main stages: the initiation phase, which is the amount of time required for chloride ions to reach the reinforcement, and the propagation phase, which is the active phase of corrosion. The inherent complexities associated with the properties of precursors and type of activators, and with the multi-physics processes, in which different transfer mechanisms (moisture, chloride, oxygen, and charge transfer) are involved and interact with each other, have been a major obstacle to predicting the durability of reinforced alkali-activated concretes in chloride environments. Alternatively, the durability of alkali-activated concretes can be assessed through testing. However, the performance-based tests that are currently available, such as the rapid chloride permeability test, the migration test or the bulk diffusion test, are only focusing on the initiation phase of the corrosion process. As a result, existing testing protocols do not capture every aspect of the material performance, which could potentially lead to misleading conclusions, particularly when involving an electrical potential to reduce the testing time. In this paper, a new performance-based test is proposed for assessing the performance of alkali-activated concretes in chloride environments, accounting for both the initiation and propagation phases of the corrosion process. The test is designed to be simple and to be completed within a reasonable time without involving any electrical potential.