Current control of a switched reluctance motor (SRM) is challenging due to nonlinearity and double saliency of the machine. A linear proportional-integral (PI)-based current controller, which is popular in other electrical machines, cannot be directly applied, as this requires a linearized machine model. This paper examines different small-signal linearized models for an SRM and identifies the model best suited for the purpose of current controller design. This paper then utilizes this linearized model to propose a fixed proportional-integral (PI)-based current controller, the parameters of which can be selected directly from the machine parameters. This paper also proposes a simple method to evaluate back-electromotive force (EMF) for the purpose of disturbance rejection during current control. The performance of the proposed fixed-PI-based control with back-EMF compensation is better than that of delta modulation in terms of current ripple; it is comparable to that of variable-gain PI with back-EMF compensation in terms of current ripple and current reference tracking. While variable-gain PI requires knowledge of the entire flux-linkage characteristics and involves calculation of controller gains in every sampling interval, the proposed method requires only limited details of the motor characteristics and is much simpler to implement.
Switching characteristics of a 1200 V, 90 A SiC MOSFET in an asymmetric H-bridge power converter are measured. Double pulse tests are carried out at different current and voltage levels. The experimental set-up and procedure are explained in detail. The switching waveforms are used to obtain the voltage and current transition times of the MOSFET. The turn-on and turn-off energy losses are also calculated. Since these are influenced by layout of the power circuit, the power converter layout and its effect on the switching waveform are reported. The turn-off energy loss is lower than the data-sheet specified value, while the turn-on energy loss is higher; the total loss is close to the data-sheet value.
10 September 2021 in IEEE Transactions on Industry Applications
This article reports design and testing of silicon carbide) devices-based three-phase asymmetric H-bridge converter capable of switching at 50 kHz and intended to drive high-speed switched reluctance machine. Electromagnetic designs of a 7.5-kW, 30 000-r/min and a 20-kW, 50 000-r/min Switched reluctance machine are presented. The 30 000-r/min machine is fabricated and characterized. A machine model is obtained from the measured characteristics. Based on the machine model, as well as drive operating variables and device data-sheet parameters, two methods are proposed for evaluating the losses in the power devices. The first method relies on machine model to obtain machine current and converter duty ratio, and thereby estimate the device losses. A second simplified method provides closed-form expressions for device losses. The proposed analytical expressions relate the machine characteristics such as inductance and saturation current with converter losses. The estimated loss is further used to predict device junction temperature. The power converter and device ratings are chosen so that the converter is suitable for both machines. The capacitor selection and sizing are discussed. Further, the power converter architecture and other subsystems of the converter are described. Test results are presented for the asymmetric H-bridge converter at 800 V dc bus voltage, 50 A of load current, and 50 kHz of switching frequency. Thermal image is presented for validation of estimated heat-sink temperature. The predicted heat-sink temperature is found to agree well with the measured temperature. The power converter is used to operate the 30 000-r/min machine at various speeds.
22 March 2018 in IEEE Transactions on Industry Applications
A novel constant current injection-based characterization scheme for the switched reluctance machine (SRM) is proposed here. Unlike conventional characterization methods where the rotor is locked at a fixed position, the current injection-based method maintains the phase current constant while the machine runs at constant speed. A novel current controller, required for the proposed constant current injection scheme, is also proposed in this paper. The predictive control-based current controller works without the machine model being available. The proposed current controller is validated experimentally and is then used to characterize a 4 kW, 1500 r/min 8/6 pole SRM. The characteristics obtained are found to be in good agreement with those obtained using conventional locked rotor tests.
17 October 2023 in IEEE Transactions on Industry Applications
Accurate tracking of reference current wave shapes is essential to obtain the desired average torque, as well as minimize torque ripple and losses of switched reluctance motor (SRM). This paper proposes a predictive control technique for accurate tracking of the current reference in an SRM drive based on a simplified piecewise linear flux-linkage model. The proposed technique eliminates extensive lookup tables and requires only a small set of model parameters, resulting in efficient memory utilization. The performance of the proposed method is evaluated for two different current shapes at various operating speeds and load torques. Simulations and experiments show that the proposed technique offers better or comparable performance over state-of-the-art lookup table-based gain-scheduling PI, sliding mode, and two existing predictive control methods. Further, the proposed technique offers the lowest torque ripple among all the above controllers. Since predictive control is based on machine models, any error in modeling can potentially lead to deterioration in tracking and instability. It has been theoretically proved that the proposed controller ensures stability even with modeling errors as high as 200% in incremental inductance. Additionally, simulation results are presented to show the effect of varying three crucial model parameters on the current tracking performance of the proposed controller. The model parameters are varied within a range of -30% to +50% of their nominal values at three different speeds. The experimental results confirm very good current tracking performance even in the presence of large modeling errors.
31 December 2020 in IEEE Transactions on Industry Applications
In this article, a method to evaluate the dc-link capacitor rms current of a switched reluctance motor (SRM) drive under different operating conditions is presented. Square current reference in both hard and soft chopping modes of pulsewidth-modulated current control is considered. By approximating the current controller response and using a recently proposed flux linkage model, the switching-cycle-average phase voltage and current are evaluated over an electrical cycle. The phase voltage and current are further used to obtain the rms values of dc-link current and capacitor current. The proposed method is also used to determine the capacitor current for low-torque-ripple current reference and single-pulse operation. The analytical predictions pertaining to different control methods under different operating conditions are verified by simulation and experimental results obtained from a 4 kW, 1500 r/min, four-phase SRM drive. While the capacitor current is found to be maximum at the lowest operating speed with hard chopping, the maximum capacitor current is observed at an intermediate speed with soft chopping, both for a given magnitude of square wave current reference. The proposed method is useful to size the dc-link capacitor and evaluate its loss in an SRM drive. Furthermore, closed-form expressions for capacitor rms current are also derived, assuming perfect tracking of square wave current reference at low speeds. These expressions bring out the dependence of capacitor rms current on the machine characteristics.