This paper presents the results of comparative fatigue tests carried out on steel S355J2N specimens cut out using different cutting methods, i.e., plasma cutting, water jet cutting, and oxyacetylene cutting. All the specimens were subjected to cyclic loading from which appropriate S-N curves were obtained. Furthermore, face-of-cut hardness and roughness measurements were carried out to determine the effect of the cutting method on the fatigue strength of the tested steel. The fatigue strength results were compared with the standard S-N fatigue curves. The fatigue strength of the specimens cut out with oxyacetylene was found to be higher than that of the specimens cut out with plasma even though the surface roughness after cutting with plasma was smaller than in the case of the other cutting technology. This was due to the significant effect of material hardening in the heat-affected zones. The test results indicate that, in comparison with the effect of the cutting technology, the surface condition of the specimens has a relatively small effect on their fatigue strength.
Do konstrukcji, które z reguły podlegają sprawdzeniu wytrzymałości na zmęczenie, należą: mosty (szczególnie kolejowe), belki podsuwnicowe, kominy wrażliwe na wzbudzenie wirowe oraz wieże i maszty. W tych konstrukcjach każdy cykl obciążenia zmęczeniowego może wywoływać zmniejszenie wytrzymałości materiału w miejscach szczególnie wrażliwych, w których występują nieregularności, np.: brzegi i granie spoin wykonanych łukowo, zakończenia żeber i blach węzłowych czy miejsca zmiany geometrii przekroju poprzecznego. Na wytrzymałość zmęczeniową konstrukcji ma wpływ wiele czynników. Do najbardziej istotnych należą wpływy: asymetrii cyklu i naprężeń średnich, koncentracji naprężeń, rodzaju obróbki i stanu warstwy wierzchniej, gatunku stali, spawania. Wpływy poszczególnych czynników odniesiono do rezultatów z badań doświadczalnych, jakie w ciągu ostatnich lat były wykonywane dla konstrukcji stalowych.
W pracy przedstawiono rozwój mechanicznychłączników zespalających w stalowo-betonowych konstrukcjach,koncentrując się na pełnym i częściowym zespoleniu belek zginanych.Omówiono różne typy łączników, w tym innowacyjnetypu perfobond strip, które eliminują potrzebę spawania łączników,tym samym upraszczając technologię wykonania konstrukcji.Wyniki wskazują, że perfobond strip zapewniają wysokąnośność i odporność na zmęczenie, co czyni je efektywnymrozwiązaniem w nowoczesnym budownictwie
W artykule omówiono wyzwania związane z zaspokajaniem potrzeb mieszkaniowych w Polsce w kontekście rosnących kosztów budowy. Przedstawiono potencjalne rozwiązanie, jakim jest szersze zastosowanie prefabrykacji, szczególnie z uwzględnieniem budownictwa modułowego i szkieletowego stalowego. Szerzej przedstawione zostały najciekawsze technologie dostępne na rynku. Podkreślono zalety tych rozwiązań, takie jak szybkość budowy, obniżenie kosztów, poprawa jakości oraz elastyczność projektowania.
Although circular strategies in construction can substantially reduce environmental impacts (EI), their effectiveness depends on aligning technological capacities with socio-economic conditions, requiring a future-oriented assessment. This study quantifies the EI of steel-frame and autoclaved aerated concrete (AAC) structures under various circular end-of-life scenarios, including multiple future lifecycles in Poland. A prospective consequential life cycle assessment (LCA) was conducted, integrating Shared Socioeconomic Pathways (SSP) for sensitivity analysis. The inventory was based on literature, spatial analysis, and expert input. Two methodological challenges were identified: lack of material quality differentiation in LCA databases, limiting reuse modelling, and difficulties in defining robust functional units across multifunctional technologies. Results indicate substantial mitigation potential from AAC recycling, particularly in single-family housing. EI of concrete recycling depends on distances and substitution of energy-intensive materials. High-quality recovery is critical for steel (>70% recycling or reuse). SSP modelling revealed the ‘crediting paradox’, highlighting the need for clear methodological boundaries.