A numerical study was performed in the present work about an Overtopping Device Wave Energy Converter (OTD-WEC) with one and two ramps incorporated in a real breakwater. The Constructal Design method was applied to evaluate the effects on the average dimensionless overtopping flow of the degrees of freedom of the device with one and two ramps. In addition, a comparison was carried out among the different geometry configurations of the OTD-WEC to determine which one presents the best hydrodynamic performance. The work used the JONSWAP spectrum and the multiphase Volume of Fluid model. It also solved the conservation equations for mass, momentum, and an equation for the transport of the volume fraction using the Finite Volume Method. Results showed that a device with a two-ramps configuration presented an average dimensionless overtopping flow 6.48% higher than those obtained for the one ramp. Present results obtained using Constructal Design theoretical recommendations about the influence of a complex configuration with four degrees of freedom over the performance of an OTD-WEC integrated into the east breakwater of the city of São José do Norte, State of Rio Grande do Sul (RS), Brazil.

The conversion of wave energy in electrical one has been increasingly studied. One example of wave energy converter (WEC) is the overtopping device. Its main operational principle consists of a ramp which guides the incoming waves into a reservoir raised slightly above the sea level. The accumulated water in the reservoir flows through a low head turbine generating electricity. In this sense, it is performed a numerical study concerned with the geometric optimization of an overtopping WEC for various relative depths: d/λ = 0.3, 0.5 and 0.62, by means of Constructal Design. The main purpose is to evaluate the effect of the relative depth on the design of the ramp geometry (ratio between the ramp height and its length: H₁/L₁) as well as, investigate the shape which leads to the highest amount of water that insides the reservoir. In the present simulations, the conservation equations of mass, momentum and one equation for the transport of volumetric fraction are solved with the finite volume method (FVM). To tackle with water-air mixture, the multiphase model Volume of Fluid (VOF) is used. Results showed that the optimal shape, (H₁/L₁)_o, has a strong dependence of the relative depth, i.e., there is no universal shape that leads to the best performance of an overtopping device for several wave conditions.

This paper presents a methodology that allows the numerical simulation of realistic sea waves, called WaveMIMO methodology, which is based on the imposition of transient discrete data as prescribed velocity on a finite volume computational model developed in Fluent software. These transient data are obtained by using the spectral wave model TOMAWAC, where the wave spectrum is converted into a series of free surface elevations treated and processed as wave propagation velocities in the horizontal (x) and vertical (z) directions. The processed discrete transient data of wave propagation velocity are imposed as boundary conditions of a wave channel in Fluent, allowing the numerical simulation of irregular waves with realistic characteristics. From a case study that reproduces the sea state occurring on March 31st, 2014, in Ingleses Beach, in the city of Florianopolis, state of Santa Catarina, Brazil, it was concluded that the WaveMIMO methodology can properly reproduce realistic conditions of a sea state. In sequence, the proposed methodology was employed to numerically simulate the incidence of irregular realistic waves over an oscillating water column (OWC) wave energy converter (WEC). From these results, the WaveMIMO methodology has proved to be a promising technique to numerically analyze the fluid-dynamic behavior of WECs subjected to irregular waves of realistic sea state on any coastal region where the device can be installed.

The present study aims to evaluate the difference in the fluid-dynamic behavior of an overtopping wave energy converter under the incidence of irregular waves based on a realistic sea state when compared to the incidence of regular waves, representative of this sea state. Thus, the sea data of three regions from the Rio Grande do Sul coast, Brazil, were considered. Fluent software was employed for the computational modeling, which is based on the finite volume method (FVM). The numerical generation of waves occurred through the imposition of the velocity boundary conditions using transient discrete values through the WaveMIMO methodology. The volume of fluid (VOF) multiphase model was applied to treat the water–air interaction. The results for the water amount accumulated in the device reservoir showed that the fluid-dynamic behavior of the overtopping converter has significant differences when comparing the two proposed approaches. Differences up to 240% were found for the water mass accumulated in the overtopping device reservoir, showing evidence that the results can be overestimated when the overtopping device is analyzed under the incidence of the representative regular waves. Furthermore, for all studied cases, it was possible to approximate the water volume accumulated over time in the overtopping reservoir through a first-degree polynomial function.

This work presents a two-dimensional numerical analysis of a wave channel and a oscillating water column (OWC) device. The main goal is to validate a methodology which uses transient velocity data as a means to impose velocity boundary condition for the generation of numerical waves. To achieve this, a numerical wave channel was simulated using regular waves with the same parameters as those used in a laboratory experiment. First, these waves were imposed as prescribed velocity boundary condition and compared with the analytical solution; then, the OWC device was inserted into the computational domain, aiming to validate this methodology. For the numerical analysis, computational fluid dynamics ANSYS Fluent software was employed, and to tackle with water–air interaction, the nonlinear multiphase model volume of fluid (VOF) was applied. Although the results obtained through the use of discrete data as velocity boundary condition presented a little disparity; in general, they showed a good agreement with laboratory experiment results. Since many studies use regular waves, there is a lack of analysis with ocean waves realistic data; thus, the proposed methodology stands out for its capacity of using realistic sea state data in numerical simulations regarding wave energy converters (WECs).