Sazzadur Chowdhury

Dr. Sazzadur Chowdhury

University of Windsor, Electrical and Computer Engineering Department, Windsor, ON, Canada

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2011 in Journal of Sensors
Verified
Journal Article
Open access
PDF file
MRMosaddequr Rahman
Mosaddequr Rahman
SCSazzadur Chowdhury
Sazzadur Chowdhury
A new highly accurate closed-form capacitance calculation model has been developed to calculate the capacitance of capacitive micromachined ultrasonic transducers (CMUTs) built with square diaphragms. The model has been developed by using a two-dimensional polynomial function that more accurately predicts the deflection curve of a square diaphragm deformed under the influence of a uniform external pressure and also takes account of the fringing field capacitances. The model has been verified by comparing the model-predicted deflection profiles and capacitance values with experimental results published elsewhere and finite element analysis (FEA) carried out by the authors for different material properties, geometric specifications, and loading conditions. New model-calculated capacitance values are found to be in excellent agreement with published experimental results with a maximum deviation of 1.7%, and a maximum deviation of 1.5% has been observed when compared with FEA results. The model can help in improving the accuracy of the design methodology of CMUT devices and other MEMS-based capacitive type sensors built with square diaphragms.

1 May 2015
Verified
Conference Paper
Closed access
WZWeiying Zeng
Weiying Zeng
MKMohammed Khalid
Mohammed Khalid
SCSazzadur Chowdhury
Sazzadur Chowdhury
This paper presents a qualitative study of FlexRay and Ethernet in in-vehicle communication networks. Although both protocols have experienced fast growth in the past years, they still have some important deficiencies that deserve attention. This qualitative study has not only outlined the important shortcomings of in-vehicle FlexRay and Ethernet, but also identified their unique competitive edges, respectively. Intensive analyses of both protocols are carried out from three key perspectives: system cost, data transmission capacity and fault detection capability. Some improving approaches have also been pointed out. It is revealed that at the current stage FlexRay is better than Ethernet in transmitting time critical signals deterministically, but has higher cost and complexity. Ethernet, though less deterministic than FlexRay, possesses much greater bandwidth and can transmit data at quite small latency and jitter. This qualitative study has indicated that both protocols need further improvement to meet the requirements of future in-vehicle networks, yet Ethernet may lead the development and expand faster.

3 December 2016 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
RMRayyan Manwar
Rayyan Manwar
TST. Simpson
T. Simpson
ABA. Bakhtazad
A. Bakhtazad
SCSazzadur Chowdhury
Sazzadur Chowdhury

12 March 2019 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
ABAref Bakhtazad
Aref Bakhtazad
SCSazzadur Chowdhury
Sazzadur Chowdhury

24 June 2016 in Sensors
Verified
Journal Article
Open access
PDF file
RMRayyan Manwar
Rayyan Manwar
SCSazzadur Chowdhury
Sazzadur Chowdhury
Experimental measurement results of a 1.75 mm × 1.75 mm footprint area Capacitive Micromachined Ultrasonic Transducer (CMUT) planar array fabricated using a bisbenzocyclobutene (BCB)-based adhesive wafer bonding technique has been presented. The array consists of 40 × 40 square diaphragm CMUT cells with a cavity thickness of 900 nm and supported by 10 µm wide dielectric spacers patterned on a thin layer of BCB. A 150 µm wide one µm thick gold strip has been used as the contact pad for gold wire bonding. The measured resonant frequency of 19.3 MHz using a Polytec™ laser Doppler vibrometer (Polytec™ MSA-500) is in excellent agreement with the 3-D FEA simulation result using IntelliSuite™. An Agilent ENA5061B vector network analyzer (VNA) has been used for impedance measurement and the resonance and anti-resonance values from the imaginary impedance curve were used to determine the electromechanical coupling co-efficient. The measured coupling coefficient of 0.294 at 20 V DC bias exhibits 40% higher transduction efficiency as compared to a measured value published elsewhere for a silicon nitride based CMUT. A white light interferometry method was used to measure the diaphragm deflection profiles at different DC bias. The diaphragm center velocity was measured for different sub-resonant frequencies using a Polytec™ laser Doppler vibrometer that confirms vibration of the diaphragm at different excitation frequencies and bias voltages. Transmit and receive operations of CMUT cells were characterized using a pitch-catch method and a −6 dB fractional bandwidth of 23% was extracted from the received signal in frequency domain. From the measurement, it appears that BCB-based CMUTs offer superior transduction efficiency as compared to silicon nitride or silicon dioxide insulator-based CMUTs, and provide a very uniform deflection profile thus making them a suitable candidate to fabricate highly energy efficient CMUTs.

4 May 2014 in International Journal of Antennas and Propagation
Verified
Journal Article
Open access
PDF file
AAAli Attaran
Ali Attaran
SCSazzadur Chowdhury
Sazzadur Chowdhury
Fabrication of a high resistivity silicon based microstrip Rotman lens using a lift-off process has been presented. The lens features 3 beam ports, 5 array ports, 16 dummy ports, and beam steering angles of ±10 degrees. The lens was fabricated on a 200 μm thick high resistivity silicon wafer and has a footprint area of 19.7 mm × 15.6 mm. The lens was tested as an integral part of a 77 GHz radar where a tunable X band source along with an 8 times multiplier was used as the RF source and the resulting millimeter wave signal centered at 77 GHz was radiated through a lens-antenna combination. A horn antenna with a downconverter harmonic mixer was used to receive the radiated signal and display the received signal in an Advantest R3271A spectrum analyzer. The superimposed transmit and receive signal in the spectrum analyzer showed the proper radar operation confirming the Rotman lens design.