Recent studies strongly suggest the possibility of more frequent extreme events as a result of the changing climate. These weather extremes, such as excessive rainfall, result in debris flow, river overflow and urban flooding, which can pose a substantial threat to the community. An effective flood model is therefore a crucial tool in flood disaster control and mitigation. A number of flood models have been established in recent years. However, the major challenge in developing effective and accurate flood models is the disadvantage of running multiple models for separate, individual conditions. Among the solutions in recent research is the development of combined 1D–2D flood modeling. Coupled 1D–2D flood modeling allows the channel flows to be represented in 1D and the overbank flow to be modeled in 2D. In order to test the efficiency of the approach, this research aims to assess the capability of the U.S. Army Corps of Engineers Hydrologic Engineering Center River Analysis System (HEC-RAS) model’s implementation of the combined 1D–2D hydraulic computation in simulating river overflow inundation. For verification, the simulation is applied to the Baeksan river levee breach event in South Korea in 2011. The simulation results show similarities of the observed data and the outputs from widely used flood models. This proves the applicability of the HEC-RAS 1D–2D coupling method as a powerful tool in simulating accurate inundations for flood events.
The Preissmann slot model is one of the most widely used models to conceptualize both free-surface and pressurized flows in urban drainage systems. Despite its simplicity and wide range of applications, numerical solutions of the Preissmann slot model suffer from the spurious oscillations, especially when flow conditions switch from free-surface flow to pressurized flow. To overcome this problem, a new hybrid numerical flux solver of the Preissmann slot model is proposed herein, in which the upwind flux solver is combined with the centered flux solver. Numerical experiments are conducted for multiple flow conditions such as typical filling, pipe-filling, and transition-flow conditions. The numerical results indicate that the proposed scheme generally outperforms the conventional flux schemes for various hydraulic conditions and wave velocities. The proposed scheme should be useful to further enhance integrated urban water modeling in which transient mixed flow conditions significantly impact the simulation accuracy during extreme floods.
The applicability of the stage-fall-discharge (SFD) method in combination with acoustic Doppler velocity meter (ADVM) data, upstream of a hydraulic structure, specifically, the Sejong-weir located in the Geum River, Korea, was examined. We developed three rating curves: a conventional simple rating curve with the data measured using an acoustic Doppler current profiler (ADCP) and floating objects, an SFD rating curve with the data measured using the ADCP and floating objects, and an SFD rating curve with the data measured using an ADVM. Because of the gate operation effect, every rating curve involved many uncertainties under 1000 m3/s (3.13 m2/s, specific discharge). In terms of the hydrograph reconstruction, compared with the conventional simple rating curve, the SFD developed using ADVM data exhibited a higher agreement with the measured data in terms of the pattern. Furthermore, the measured discharge over 1000 m3/s primarily ranged between 97.5% and 2.5% in the graph comparing the ratio of the median and observed discharge. Based on this experiment, it is confirmed that the SFD rating curve with data to represent the backwater effect, such as ADVM data, can reduce the uncertainties induced by the typical rating curve
30 September 2014 in Journal of the Korean Association of Geographic Information Studies
During extreme floods caused by climate change, reliable flow discharge data are essential for successful reservoir operation to mitigate downstream flood damage. Generally, the flow discharge is computed using the rating curve (RC) established from the relationship between the flow rate and water stage level. Determining the parameters of rating curves is subject to uncertainties related to the difficulties and limitations of flow monitoring in covering a wide range of flow variations. Especially at river confluences, the uncertainties are pronounced when floods occur owing to several factors such as roughness change, backwaters, and levee overflow. The Seomjin River Basin in Korea suffered from flood inundation that occurred at the tributary confluence during an extreme flood in 2020. To identify a reliable flow rate of the main stream and tributary, this study proposes an indirect flow assessment scheme using a 1D hydrodynamic simulation model to find the best simulated water level in an iterative manner based on Monte Carlo (MC) simulations. With a large amount of discharge data generated from random-number combinations, it is possible to obtain the best results automatically by specifying the reliability limitation considering the uncertainty of the predetermined RC parameters associated with the roughness coefficient. Nash Sutcliffe Efficiency (NSE) was incorporated to evaluate the reproduced water level to meet the threshold specified for NSE ≥ 0.75. The simulated flowrates computed from the revised RC and roughness coefficients revealed an error range of 8%–36.6% compared with the design flood. The approach proposed in this study is applicable for determining the valid parameters necessary to create a revised RC at an existing water level gauge station, where the uncertainties of the RC are pronounced, particularly in the vicinity of the channel confluence.