Kosuke Hayashi

Prof. Dr. Kosuke Hayashi

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 August 2014 in Soft Matter
Verified
Journal Article
Closed access
PDF file
YKYusuke Kagawa
Yusuke Kagawa
TIToru Ishigami
Toru Ishigami
KHKosuke Hayashi
Kosuke Hayashi
HFHiromi Fuse
Hiromi Fuse
YMYasushi Mino
Yasushi Mino
Hideto MatsuyamaHideto Matsuyama
Hideto Matsuyama
In this paper, we investigated the demulsification behavior of oil-in-water (O/W) emulsions during membrane permeation in the oil–water separation process using a numerical simulation approach. To accurately deal with the large deformation of the oil–water interface by coalescence and wetting, and to estimate the volume of the coalesced oil droplet, the coupled level set and volume-of-fluid method was used as the interface capturing method. We applied the simulation model to the permeation of O/W emulsions through a membrane pore, and then investigated the effects of the wettability of the membrane surface, filtration flux, and pore size on the demulsification efficiency. The results showed that oil droplets were likely to coalesce on the outlet membrane surface. High wettability on the membrane surface and low fluid velocity inside the pore increased the demulsification efficiency. This is the first work to numerically simulate the demulsification behavior of emulsions through membranes in the oil–water separation process.

10 December 2014 in Journal of Nuclear Science and Technology
Verified
Journal Article
Open access
TKTakayoshi Kusunoki
Takayoshi Kusunoki
MMMichio Murase
Michio Murase
YFYuki Fujii
Yuki Fujii
TNTakahiro Nozue
Takahiro Nozue
KHKosuke Hayashi
Kosuke Hayashi
ATAkio Tomiyama
Akio Tomiyama
The purpose of this study is to derive a counter-current flow limitation (CCFL) correlation and evaluate its uncertainty for steam generator (SG) U-tubes in a pressurized water reactor (PWR). Experiments were conducted to evaluate effects of the liquid viscosity on CCFL characteristics using air–40 wt% or air–60 wt% glycerol water solution and saturated steam–water at atmospheric pressure with vertical pipes simulating the lower part of the SG U-tubes. The steam–water experiments confirmed that CCFL characteristics could be expressed in terms of the Wallis parameters (JG* and JL*) for the pipe diameters of D = 14, 20, and 27 mm. A CCFL correlation was derived using the ratio μG/μL of the viscosities of the gas and liquid phases, μG and μL, as a correction term representing effects of fluid properties, where JG*1/2(μG/μL)−0.07 was expressed by a cubic function of JL*1/2(μG/μL)0.1. In the correlation, the constant C indicating the value of JG*1/2(μG/μL)−0.07 at JL* = 0 was (1.04 ± 0.05), and this uncertainty of ±0.05 would cover most of the previous experimental data including the ROSA-IV/LSTF data at 1, 3, and 7 MPa.

1 June 2012 in The Journal of Computational Multiphase Flows
Verified
Journal Article
Open access
KHKosuke Hayashi
Kosuke Hayashi
RRRoberto Rojas
Roberto Rojas
TSTakeshi Seta
Takeshi Seta
ATAkio Tomiyama
Akio Tomiyama
An immersed boundary-lattice Boltzmann method (IB-LBM) using a two-relaxation time model (TRT) is proposed. The collision operator in the lattice Boltzmann equation is modeled using two relaxation times. One of them is used to set the fluid viscosity and the other is for numerical stability and accuracy. A direct-forcing method is utilized for treatment of immersed boundary. A multi-direct forcing method is also implemented to precisely satisfy the boundary conditions at the immersed boundary. Circular Couette flows between a stationary cylinder and a rotating cylinder are simulated for validation of the proposed method. The method is also validated through simulations of circular and spherical falling particles. Effects of the functional forms of the direct-forcing term and the smoothed-delta function, which interpolates the fluid velocity to the immersed boundary and distributes the forcing term to fixed Eulerian grid points, are also examined. As a result, the following conclusions are obtained: (1) the proposed method does not cause non-physical velocity distribution in circular Couette flows even at high relaxation times, whereas the single-relaxation time (SRT) model causes a large non-physical velocity distortion at a high relaxation time, (2) the multi-direct forcing reduces the errors in the velocity profile of a circular Couette flow at a high relaxation time, (3) the two-point delta function is better than the four-point delta function at low relaxation times, but worse at high relaxation times, (4) the functional form of the direct-forcing term does not affect predictions, and (5) circular and spherical particles falling in liquids are well predicted by using the proposed method both for two-dimensional and three-dimensional cases.

5 February 2014 in Journal of Nuclear Science and Technology
Verified
Journal Article
Open access
KHKosuke Hayashi
Kosuke Hayashi
SHShigeo Hosokawa
Shigeo Hosokawa
ATAkio Tomiyama
Akio Tomiyama
Numerical simulations of bubbly flows in a four by four rod bundle are carried out using a multi-fluid model to examine effects of the numerical treatment of phase distribution and drag model. The transport equations of bubble number density and void fraction are used as the continuity equation of the gas phase. Two drag models are tested: one of them accounts for the bubble deformation (aspect ratio), whereas the other does not. The rod diameter, the rod pitch and the hydraulic diameter of the rod bundle are 10, 12.5 and 9.1 mm, respectively. The gas and liquid volume fluxes are JG = 0.06 m/s and JL = 0.9 and 1.5 m/s, respectively. The bubble diameter ranges from 1 to 5 mm. Comparisons between the numerical and measured data show that (1) the restriction on bubble lateral motion due to the presence of rods can be taken into account by using the transport equation of bubble number density, whereas that of the void fraction cannot deal with the restriction and causes large errors in the distribution of void fraction and (2) the reduction in the bubble-relative velocity near the wall is predictable by using the drag model accounting for the bubble deformation effect.

4 March 2024 in Chemical Engineering Research and Design
Verified
Journal Article
Closed access
TMTakumi Mori
Takumi Mori
RIRyota Igarashi
Ryota Igarashi
KHKosuke Hayashi
Kosuke Hayashi
RKRyo Kurimoto
Ryo Kurimoto
ATAkio Tomiyama
Akio Tomiyama

17 February 2025 in International Journal of Multiphase Flow
Verified
Journal Article
Open access
KHKosuke Hayashi
Kosuke Hayashi
YMYuya Motoki
Yuya Motoki
DLDominique Legendre
Dominique Legendre
ATAkio Tomiyama
Akio Tomiyama