The building sector is one of the key energy consumers worldwide. Fuel cell micro-Cogeneration Heat and Power systems for residential and small commercial applications are proposed as one of the most promising innovations contributing to the transition towards a sustainable energy infrastructure. For the application and the diffusion of these systems, in addition to their environmental performance, it is necessary, however, to evaluate their economic feasibility. In this paper a life cycle assessment of a fuel cell/photovoltaic hybrid micro-cogeneration heat and power system for a residential building is integrated with a detailed economic analysis. Financial indicators (net present cost and payback time are used for studying two different investments: reversible-Solid Oxide Fuel Cell and natural gas SOFC in comparison to a base scenario, using a homeowner perspective approach. Moreover, two alternative incentives scenarios are analysed and applied: net metering and self-consumers’ groups (or energy communities). Results show that both systems obtain annual savings, but their high capital costs still would make the investments not profitable. However, the natural gas Solide Oxide Fuel Cell with the net metering incentive is the best scenario among all. On the contrary, the reversible-Solid Oxide Fuel Cell maximizes its economic performance only when the self-consumers’ groups incentive is applied. For a complete life cycle cost analysis, environmental impacts are monetized using three different monetization methods with the aim to internalize (considering them into direct cost) the externalities (environmental costs). If externalities are considered as an effective cost, the natural gas Solide Oxide Fuel Cell system increases its saving because its environmental impact is lower than in the base case one, while the reversible-Solid Oxide Fuel Cell system reduces it.
Contamination by plastics is one of the major causes of pollution of the terrestrial environment. Fragmentation of plastics into micro and nano particles may result in negative interactions between polymers and terrestrial ecosystems. The effects of nano (20 nm) and submicron (200 nm) fluorescent polystyrene (PS) particles, at different concentrations (0.01, 0.1, 1 g L−1), were analysed on chicory plant (Cichorium endivia L.), considering the following endpoints: germination percentage and seedling development after 7 and 14 days exposure; genotoxic effects; polyphenols and photosynthetic pigments content, antioxidant activity; absorption and translocation of PS particles in the seedling tissues. The results indicated no negative effects on germination of both PS particles' sizes at any concentration; seedlings elongation was affected by 1 g L−1 of 20 nm PS after 7 days exposure. Cytological analysis revealed no mitotic activity inhibition, but an uprising of chromosomal abnormalities in all treatments. Interestingly, photosynthetic pigments always increased after PS exposure. Seedlings treated with 20 nm PS showed intense fluorescence in the roots of 7 days and in the shoots of 14 days, while 200 nm PS treated seedlings exhibited low fluorescence. Electron microscopy and infrared spectroscopy confirmed 20 nm PS internalization and transport inside the plant tissue and a reduced presence of 200 nm PS. These results suggest the importance not only of particle size in plastic internalization in plant tissues, but also of cytological damages induced by particles too large to be bioaccumulated. From both aspects, consequences may arise for plant fitness, food safety and human health.
Polydopamine has the capacity to adhere to a large variety of materials and this property offers the possibility to bind nanoparticles to solid surfaces. In this work, magnetite nanoparticles were deposited on gold substrates coated with polydopamine films. The aim of this work was to investigate the effects of the composition and morphology of the PDA layers on the sticking of magnetite nanoparticles. The polydopamine coating of gold surfaces was achieved by the oxidation of alkaline solutions of dopamine with various reaction times. The length of the reaction time to form PDA was expected to influence the composition and surface roughness of the PDA films. Magnetite nanoparticles were deposited on these polydopamine films by immersing the samples in aqueous dispersions of nanoparticles. The morphology at the nanometric scale and the composition of the surfaces before and after the deposition of magnetite nanoparticles were investigated by means of AFM and XPS. We found that the amount of magnetite nanoparticles on the surface did not vary monotonically with the reaction time of PDA formation, but it was at the minimum after 20 min of reaction. This behavior may be attributed to changes in the chemical composition of the coating layer with reaction time.
Because of their capacity to bind metals, metal chelators are primarily employed for therapeutic purposes, but they can also find applications as colorimetric reagents and cleaning solutions as well as in soil remediation, electroplating, waste treatment, and so on. For instance, iron-chelation therapy, which is used to treat iron-overload disorders, involves removing excess iron from the blood through the use of particular molecules, like deferoxamine, that have the ability to chelate the metal. The creation of bioinspired and biodegradable chelating agents is a crucial objective that draws inspiration from natural products. In this context, starting from bioavailable molecules such as maltol and pyrogallol, new molecules have been synthetized and characterized by potentiometry, infrared spectroscopy and cyclic voltammetry. Finally, the ability of these to bind iron has been investigated, and the stability constants of ferric complexes are measured using spectrophotometry. These compounds offer intriguing scaffolds for an innovative class of versatile, multipurpose chelating agents.
In the present work, we investigated the role of polydopamine coatings in anchoring TiO2 P25 nanoparticles on gold and ITO surfaces. For this purpose, we studied the adhesion of polydopamine-coated aggregates of TiO2 nanoparticles on bare substrates and of aggregates of bare TiO2 nanoparticles on polydopamine-coated substrates. Coating with polydopamine was accomplished by oxidation in air of alkaline aqueous dopamine solutions in which the nanoparticles or the substrates were immersed. Dynamic light scattering, Fourier transform infrared spectroscopy, and transmission electron microscopy were used for the chemical and morphological characterization of aggregates of the nanoparticles. The adhesion of aggregates of the nanoparticles on the substrates was evaluated by means of AFM and XPS. The results of this study suggest that the adhesion of TiO2 P25 nanoparticles on polydopamine films, as well as of polydopamine-coated TiO2 P25 nanoparticles, is a balance of several contributions: chemical interactions, electrostatic interactions, and coating roughness. Electrostatic attraction and repulsion between nanoparticles and the substrate appear to play an important role, as indicated by the ζ-potential values of nanoparticles and substrates.