In order to improve the motion smoothness while maintaining the machining efficiency of the non-uniform rational B-spline (NURBS) interpolation, a novel jerk-continuous acceleration/deceleration (ACC/DEC) algorithm and the corresponding feedrate scheduling method are proposed in this paper. The polynomial and trigonometric functions are combined to construct the jerk-continuous ACC/DEC profile. Meanwhile, to reduce the computational load of feedrate scheduling, a proportional control method is proposed to determine the form of the jerk profile, which also improves the flexibility of feedrate control. Therefore, the maximum jerk and acceleration can be maintained to achieve higher machining efficiency compared with the conventional trigonometric methods, while the feedrate scheduling process is far simpler than the polynomial methods with continuous jerk. In addition, to improve the machining accuracy and motion smoothness, the round-off error caused by cycle sampling is also considered in feedrate scheduling and real-time interpolation. The proposed ACC/DEC algorithm is simplified to achieve the round-off error compensation, which can guarantee the continuity of jerk profile. A series of simulations and experiments for two NURBS curves are conducted to verify the good performance and applicability of the proposed method.
To improve the interpolation accuracy for the Non-Uniform Rational B-Spline (NURBS) curves, this paper proposes a novel bidirectional adaptive feedrate scheduling (BAFS) method based on S-shaped acceleration/deceleration (ACC/DEC) algorithm. The NURBS interpolator with the proposed BAFS method is also presented. The BAFS method has two meanings. Firstly, to consider the continuous constraints of feedrate especially in the areas near the endpoints of each NURBS curve segment, an adaptive feedrate scheduling method is designed, which can improve the interpolation accuracy compared with the conventional method only considering the constraints of endpoints. Secondly, a bidirectional adaptive interpolation strategy including an adaptive task scheduling method and a meeting processing method is proposed to conduct the acceleration and deceleration interpolation stages of each NURBS segment separately in two directions. The two directions interpolation can be realized orderly by the adaptive task scheduling and the smoothness of feedrate profile can be guaranteed by the meeting processing method whose solvability is also proved. Therefore, the feedrate constraints at both the start and end points areas can be considered, which can improve the interpolation accuracy. Meanwhile, the round-off errors caused by cycle sampling are also considered and compensated in the bidirectional feedrate scheduling process to maintain the motion smoothness. In addition, an optimized look-ahead strategy is designed to ensure the correctness of the endpoints feedrate. Finally, a series of simulations and experiments are conducted to validate the good performance and applicability of the proposed method.
1 January 2019 in International Journal of Advanced Robotic Systems
Considering the joint elasticity, a novel dynamic parameter identification method is proposed for general industrial robots only with motor encoders. Firstly, the unknown parameters of the elastic joint dynamic model are analyzed and divided into two types. The first type is the motion-independent parameter only including the joint stiffness, which can be identified by the static force/torque-deformation experiments without the dynamic model. The second type is the motion-dependent parameter composed of the rest of the parameters, which needs the dynamic excitation experiments. Therefore, these two types of parameters can be identified separately. Meanwhile, it is found that the rotor inertia parameters can be obtained from the manufacturer, which reduces the identification difficulty of other parameters. After obtaining the rotor inertia and joint stiffness, an approximate processing algorithm is proposed considering the motor friction to establish the linear identification model of other parameters. Hence, the least squares can be employed to identify the parameters, and the independence of the inertia and joint viscous friction parameters are not affected. Meanwhile, the exciting trajectories can be optimized throughout the robot workspace, which reduces the effect of measurement noise on identification accuracy. With the proposed separated identification strategy and approximate processing algorithm, the dynamic parameters can be obtained precisely without double encoders on each joint. Finally, a series of simulations are conducted to evaluate the good performance of the proposed method.
16 December 2019 in Arabian Journal for Science and Engineering
This article considers finite-time trajectory tracking control problem for robotic manipulators with parameter uncertainties and external disturbances. A finite-time controller that achieves high precision and strong robustness is proposed without the requirement of the exact dynamic model. First, a novel finite-time model-assisted extended state observer is designed to compensate the system uncertainties with complex and uncertain dynamics. Then, a composite finite-time controller is developed for trajectory tracking control with the help of finite-time model-assisted extended state observer. Compared to the classic extended state observer, it is proved that the estimation error of finite-time model-assisted extended state observer can be stabilized in finite time. Meanwhile, the finite-time convergence of the closed-loop system with the proposed controller can also be proved through Lyapunov’s stability theory. A variable structure term is employed to compensate the estimation errors of finite-time model-assisted extended state observer. The validity of the control scheme is demonstrated by simulations and experiments.
30 July 2021 in The International Journal of Advanced Manufacturing Technology