The computer-controlled optical surface (CCOS) can process good optical surfaces, but its edge effect greatly affects its development and application range. In this paper, based on the two fundamental causes of the CCOS’s edge effect—namely the nonlinear variation of edge pressure and the unreachable edge removal—a combined polishing method of double-rotor polishing and spin-polishing is proposed. The model of the combined polishing method is established and theoretically analyzed. Combined with the advantages of double-rotor polishing and spin-polishing, the combined polishing process can achieve full-aperture machining without pressure change. Finally, the single-crystal silicon sample with a diameter of 100 mm is polished by the combined polishing process. The results show that, compared with the traditional CCOS polishing, the residual error of the sample after the combined polishing process is more convergent, and the edge effect is effectively controlled.

With the development of short wavelength optics, high requirements are put forward for the full frequency errors of optical elements, while the processing efficiency and surface quality of traditional polishing methods are difficult to meet their requirements. In this paper, a fluid lubricated polishing method is proposed by combining non-Newtonian fluid with traditional polishing methods. According to Preston equation and shear thickening principle, the tool influence function of fluid lubricated polishing is established and verified by experiments. The results show that the fluid lubricated polishing has a very good convergence ability to the full frequency error of the workpiece. In addition, the convergence rate of fluid lubricated polishing on roughness is about twice that of chemical mechanical polishing. Finally, fluid lubricated polishing extends Preston from Newtonian fluid polishing to non-Newtonian fluid polishing.

X ray mirrors are symmetrical workpieces along the length and width and are widely used in various optical systems. Unlike the center-symmetric circular mirror, it is more difficult to suppress the edge effect of the x ray mirror during the polishing process, which greatly limits the polishing accuracy and polishing efficiency. Based on this, the unique edge effect of x ray mirrors is investigated in depth in this paper. First, the causes and distribution laws of the edge effect of the x ray mirror were obtained by analyzing the inherent structure of the computer controlled optical surface (CCOS) and the motion trajectory of the polishing tool. Second, a mathematical model was established based on the material removal states of different regions on the x ray mirror. Finally, a combined polishing process based on the influence function of different shaped tools is proposed and experimentally verified. The results show that the edge effect on the x ray mirror is significantly weakened and its surface errors peak to valley (PV) and RMS are increased by 21.5 times and 47.9 times, respectively. This indicates that the combined polishing process has a good suppression effect on the edge effect of the x ray mirror.

With the development of optoelectronic information technology, high-performance optical systems require an increasingly higher surface accuracy of optical mirrors. The fast tool servo (FTS) based on the piezoelectric actuator is widely used in the compensation machining of high-precision optical mirrors. However, with the low natural frequency of mechanical structures, hysteresis of the piezoelectric actuators, and phase delay of the control systems, conventional FTS systems face problems such as a low working frequency and a large tracking error. This study presents a method for the design of a high-performance FTS system. First, a flexure hinge servo turret with a high natural frequency was designed through multi-objective optimization and finite element simulations. Subsequently, a composite control algorithm was proposed, targeting the problems of hysteresis and phase delay. The modified Prandtl–Ishlinskii inverse hysteresis model was used to overcome the hysteresis effect and a zero-phase error tracker was designed to reduce the phase error. The experimental results reveal that the tracking error of the designed FTS system was <10% in the full frequency range (0–1000 Hz).

In order to obtain ultra-smooth surfaces of single-crystal silicon in ultra-precision machining, an accurate study of the deformation mechanism, mechanical properties, and the effect of oxide film under load is required. The mechanical properties of single-crystal silicon and the phase transition after nanoindentation experiments are investigated by nanoindentation and Raman spectroscopy, respectively. It is found that pop-in events appear in the theoretical elastic domain of single-crystal silicon due to the presence of oxide films, which directly leads the single crystal silicon from the elastic deformation zone into the plastic deformation zone. In addition, the mechanical properties of single-crystal silicon are more accurately measured after it has entered the full plastic deformation.