In this work, TiO₂/CdS nanocomposites with co-exposed {101}/[111]-facets (NH4F-TiO2/CdS), {101}/{010} facets (FMA-TiO2/CdS), and {101}/{010}/[111]-facets (HF-TiO2/CdS and Urea-TiO2/CdS) were successfully synthesized through a one-pot solvothermal method by using [Ti₄O₉]²⁻ colloidal solution containing CdS crystals as the precursor. The crystal structure, morphology, specific surface area, pore size distribution, separation, and recombination of photogenerated electrons/holes of the TiO₂/CdS nanocomposites were characterized. The photocatalytic activity and cycling performance of the TiO₂/CdS nanocomposites were also investigated. The results showed that as-prepared FMA-TiO₂/CdS with co-exposed {101}/{010} facets exhibited the highest photocatalytic activity in the process of photocatalytic degradation of methyl orange (MO), and its degradation efficiency was 88.4%. The rate constants of FMA-TiO₂/CdS was 0.0167 min⁻¹, which was 55.7, 4.0, 3.7, 3.5, 3.3, and 1.9 times of No catalyst, CdS, HF-TiO₂/CdS, NH₄F-TiO₂/CdS, CM-TiO₂, Urea-TiO₂/CdS, respectively. The highest photocatalytic activity of FMA-TiO₂/CdS could be attributed to the synergistic effects of the largest surface energy, co-exposed {101}/{010} facets, the lowest photoluminescence intensity, lower charge-transfer resistance, and a higher charge-transfer efficiency.

The Mg–Gd–Y–Zn–Zr alloy containing a long period stacking ordered (LPSO) phase was subjected to multi-pass deformation by means of a multi-directional forging process, and the microstructure evolution and the influence of the LPSO phase on its dynamic recrystallization (DRX) were studied. The results showed that multi-directional forging can effectively refine the grain with the DRX fraction increased, and DRXed grains lead to the decrease of the texture intensity, which can significantly improve the mechanical properties of the alloy. The different morphologies of the LPSO phase have different degrees of promotion relative to DRX behavior. The lamellar LPSO phase with kinks promoted dislocation plugging, where there could be a potential nucleation site for DRX grains. The fragmented lamellar LPSO phase promoted the DRX process through the particle-stimulated nucleation mechanism, and the block-shaped phase was more prone to stress concentration, which promoted DRX. These effects resulted in continuous grain refinement and a more uniform microstructure.

Rotating backward extrusion (RBE) is one of severe plastic deformation (SPD) methods used to produce cylindrical components with a very large strain by a single pass. In this study, the microstructure and texture evolution in the different regions of Mg-12Gd-4Y-2Zn-0.5Zr (wt.%) alloys via RBE process were investigated by using optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM) and electron back-scatter diffraction (EBSD). The results showed that the cup-shaped sample formed by RBE process exhibited typical gradient microstructure expanding from its inner wall to outer wall along the radial direction (RD). The average grain size of the RBEed sample decreased when the radius decreased from the edge region to the center region along the RD, which was attributed to the different strains and strain rates in the different regions. It also could be observed that the center region showed highest deformation and the edge region exhibited the lowest deformation in the RBEed sample along the RD. In addition, the grain refinement mechanisms of the experimental alloy containing long-period stacking ordered (LPSO) phases after RBE with 100 N were continuous dynamic recrystallization (CDRX), discontinuous dynamic recrystallization (DDRX) and particle stimulated nucleation (PSN).