To accelerate bridge construction, U-bar details were proposed to connect the adjacent precast box girders and replace the original welded-loop details in longitudinal joint design. Static loading tests were conducted, and the failure mode, flexural strength, and cracking behavior of the specimens with welded-loop details and U-bar details were compared. The influence of the U-bar longitudinal spacing, the joint concrete strength, and U-bar lap length on joint performance was also considered. The test results show that although the specimen with U-bar details had the same strength as that of specimen with welded-loop details, it cracked earlier and faster, but it still met the code requirement on maximum crack width. Longitudinal spacing of U-bars has a significant influence on joint performance. Interface cracking occurred for all specimens, considering the actual construction sequence. The tested flexural capacities of specimens with U-bar details were compared with theoretical predictions based on two existing strut-and-tie (STM) models, and the accuracy of these two models was evaluated.
In reinforced concrete (RC) structures, new-to-old concrete interfaces are widely present due to precast splices, repairs, and construction joints. In this paper, both monolithic and segmental specimens were fabricated with five kinds of water–cement ratios, including ordinary and high-strength concrete. The impressed current-accelerated corrosion test was used, and the degree of reinforcement corrosion was controlled by Faraday’s Law. In the accelerated corrosion process, the concrete surface cracking, steel corrosion, and mechanical properties of the corroded steels in the segmental specimens were investigated and compared with monolithic specimens considering the pouring method, concrete strength, and the strength difference between new and old concrete. The prediction of concrete cracking time was also discussed. The results indicated that, for the monolithic specimens, longitudinal cracks could be observed on the ordinary concrete surface, while no cracks were produced on a high-strength concrete surface; only the rust leaked out at the ends. For the segmental specimens, both longitudinal and transverse cracks were produced on an ordinary concrete surface, while only transverse cracks were produced at the high-strength new-to-old concrete interfaces. The steel embedded in the segmental specimens suffered more sectional loss at the new-to-old concrete interfaces. An influence coefficient based on the section loss of the rebar was proposed to evaluate the influence of interfaces on the rust uniformity of rebars. When there were differences in strength between new and old concrete, the influence of the interface on the uniformity of steel bar cross-section loss slightly increased. Based on available theoretical analysis for uniform corrosion, the concrete cracking time of the monolithic specimens was predicted, which was basically consistent with experimental phenomena. However, further research is needed to predict the service life of segmental specimens with new-to-old concrete interfaces.
High temperatures can enhance the chloride diffusion coefficient and this poses a threat to reinforced concrete (RC) piles. This study intends to propose predictive models that can evaluate the service life and lateral bearing behaviour of reinforced concrete piles subjected to marine environments and varying temperatures. The models show that temperature can accelerate the diffusion rate of chloride and increase the concentration of free chloride in concrete. The distribution law of chloride concentration is obtained by considering the ageing effect as well. Deterministic and probabilistic models are proposed to assess the time to corrosion initiation and propagation. The stiffness degradation coefficient is introduced in the analysis of the lateral bearing capacity of RC piles. The results show that high temperature can decrease the service life of piles and the life spans obtained from deterministic and probabilistic methods are similar; however, the predictions of the latter are more conservative. Temperature can enhance the current density and boost corrosion products, which leads to pile cracking. The rust appearing on the steel surface would make the stiffness degradation coefficient drop sharply. The lateral bearing capacity analysis is conducted from the perspectives of shear force, displacement and bearing moment of the piles.
The depth of cracks propagating inside reinforcement concrete (RC) components is barely able to be detected by visual inspection. Without any help from facilities, crack width can provide us with a proper way to explore the depth of cracks developing. Therefore, this paper tried to explore the correlation between crack width on the surface and crack depth. A static loading test was conducted on eight RC beams, considering the variation of concrete strength, cover, and reinforcement ratio. The test results indicate that concrete strength has a certain impact on cracking load and the propagation of cracks is mainly related to reinforcement ratio. The linear changes in load and crack width can be found. Originally, crack depth markedly increased with loading, but when restricted by compression zone of concrete and the height of beams, crack depth stopped extending finally. The correlation between crack width and crack depth was analyzed by studying work phases of a cross-section and experimental data. The fitting function achieved in this paper was determined to be a good agreement between the theoretical and the experimental relationship.
21 November 2025 in Arabian Journal for Science and Engineering