We report electrical characterization of monolayer molybdenum disulfide (MoS2) devices using a thin layer of polymer electrolyte (PE) consisting of poly(ethylene oxide) (PEO) and lithium perchlorate (LiClO4) as both a contact-barrier reducer and channel mobility booster. We find that bare MoS2 devices (without PE) fabricated on Si/SiO2 have low channel mobility and large contact resistance, both of which severely limit the field-effect mobility of the devices. A thin layer of PEO/LiClO4 deposited on top of the devices not only substantially reduces the contact resistance but also boost the channel mobility, leading up to three-orders-of-magnitude enhancement of the field-effect mobility of the device. When the PE is used as a gate medium, the MoS2 field-effect transistors exhibit excellent device characteristics such as a near ideal subthreshold swing and an on/off ratio of 106 as a result of the strong gate-channel coupling.
We report ferromagnetism above in ( in at. %) sputtered thin films. For , a large magnetic moment of was observed, which decreases monotonically with increasing . We find evidence that the ferromagnetic moment is due to Cu-O planar nanophase inclusions in ZnO basal planes. The presence of CuO nanophase is confirmed by transmission electron microscopy, x-ray diffraction, and Raman spectroscopy studies. These inclusions are present even for , where Cu-O structures of a few nanometers in size are observed. Field-cooled and zero-field-cooled magnetization measurements show a bifurcation for temperatures below .
11 December 2008 in Journal of Physics: Condensed Matter
We have synthesized a range of transition-metal-doped BiFeO(3) thin films on conducting silicon substrates using a spin-coating technique from metal-organic precursor solutions. Bismuth, iron and transition-metal-organic solutions were mixed in the appropriate ratios to produce 3% transition-metal-doped samples. X-ray diffraction studies show that the samples annealed in a nitrogen atmosphere crystallize in a rhombohedrally distorted BiFeO(3) structure with no evidence for any ferromagnetic secondary phase formation. We find evidence for the disappearance of the 404 cm(-1) Raman mode for certain dopants indicative of structural distortions. The saturation magnetization of these BiFeO(3) films has been found to increase on doping with transition metal ions, reaching a maximum value of 8.5 emu cm(-3) for the Cr-doped samples. However, leakage current measurements find that the resistivity of the films typically decreases with transition metal doping. We find no evidence for any systematic variation of the electric or magnetic properties of BiFeO(3) depending on the transition metal dopant, suggesting that these properties are determined mainly by extrinsic effects arising from defects or grain boundaries.
We have studied the temperature dependence of the Raman spectra of ceramic bulk and thin-film samples of polycrystalline 0.1, 0.2, and 0.3) in the range between room temperature and 350 °C. The ferroelectric to paraelectric phase-transition temperatures have been estimated from the loss of intensity for several phonon modes belonging to the tetragonal phase when the samples transform to the paraelectric cubic phase. Similar to single crystalline broad first-order Raman features are found to persist well beyond in all the samples studied here. For bulk samples, the estimated values of from the Raman studies agree well with the values determined from the anomaly in the dielectric constant versus temperature measurements. For thin films, however, the temperature measurements of the dielectric constant do not show any anomaly and the Raman signature viz., the disappearance of several phonon modes at is used for determining We find that the values of in thin films are higher than those of the bulk samples. This is attributed to the presence of intergrain stresses in the submicron size grains in the thin films which might prevent a complete phase transformation at the expected bulk Furthermore, a new Raman mode has been seen at ∼620 in all the thin-film samples but not in bulk ceramics at all temperatures. This mode has also been observed in polycrystalline bulk powder under high pressure and it most probably originates from the strain in the grain-boundary regions.