Krishn Das Patel

Dr. Krishn Das Patel

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 June 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
KPKrishn Das Patel
Krishn Das Patel
FJFuh-Shyang Juang
Fuh-Shyang Juang
HWHao-Xuan Wang
Hao-Xuan Wang
CJChong-Zhe Jian
Chong-Zhe Jian
JCJia-You Chen
Jia-You Chen
In this study, white organic light-emitting diodes (OLEDs) consisting of red quantum dots (RQD) and green quantum dots (GQD) were investigated. These are the most exciting new lighting technologies that have grown rapidly in recent years. The white OLED development processes used consisted of the following methods: (a) fabrication of a blue single-emitting layer OLED, (b) nanoimprinting into QD photoresists, and (c) green and red QD photoresists as color conversion layers (CCL) excited by blue OLEDs. To fabricate the blue OLED, the HATCN/TAPC pair was selected for the hole injection/transport layer on ITO and TPBi for the electron transport layer. For blue-emitting material, we used a novel polycyclic framework of thermally activated delayed fluorescence (TADF) material, ν-DABNA, which does not utilize any heavy metals and has a sharp and narrow (FWHM 28 nm) electroluminescence spectrum. The device structure was ITO/HATCN (20 nm)/TAPC (30 nm)/MADN: ν-DABNA (40 nm)/TPBi (30 nm)/LiF (0.8 nm)/Al (150 nm) with an emitting area of 1 cm × 1 cm. The current density, luminance, and efficiency of blue OLEDs at 8 V are 87.68 mA/cm2, 963.9 cd/m2, and 1.10 cd/A, respectively. Next, the bottom emission side of the blue OLED was attached to nanoimprinted RQD and GQD photoresists, which were excited by the blue OLED in order to generate an orange and a green color, respectively, and combined with blue light to achieve a nearly white light. In this study, two different excitation architectures were tested: BOLED→GQD→RQD and BOLED→RQD→GQD. The EL spectra showed that the BOLED→GQD→RQD architecture had stronger green emissions than BOLED→RQD→GQD because the blue OLED excited the GQD PR first then RQD PR. Due to the energy gap architectures in BOLED-GQD-RQD, the green QD absorbed part of the blue light emitted from the BOLED, and the remaining blue light penetrated the GQD to reach the RQD. These excited spectra were very close to the white light, which resulted in three peaks emitting at 460, 530, and 620 nm. The original blue CIE coordinates were (0.15, 0.07). After the excitation combination, the CIE coordinates were (0.42, 0.33), which was close to the white light position.

21 June 2022 in International Journal of Photoenergy
Verified
Journal Article
Open access
PDF file
FJFuh-Shyang Juang
Fuh-Shyang Juang
KPKrishn Das Patel
Krishn Das Patel
KHKuo-Chun Huang
Kuo-Chun Huang
WJWen-Xaing Juang
Wen-Xaing Juang
JCJeng-Yue Chen
Jeng-Yue Chen
LHLin-Ann Hong
Lin-Ann Hong
In this study top emission organic light-emitting diodes (TE-OLED) were successfully fabricated on flexible PET/multilayer disordered silver nanonetwork (MDSN) substrate with conventional LiF/Al as a semitransparent cathode and Ag as a reflective anode. The effects of the hole injection layer, anode buffer layer, and an electron injection layer on the luminescence characteristics of TE-OLEDs were investigated. At first, the thickness of cathode Al is adjusted based upon the overall transmittance of the top-emission cathode and its conductivity. There is a high energy barrier for the hole between the work function of the anode Ag (4.2eV) and the NPB highest occupied molecular orbital (HOMO) energy level (5.5eV), which is not favorable for hole injection. This study tested four types of hole injection layer (HIL) materials. Finally, MoO3 was selected as an optimal HIL material, and the optimum thickness was adjusted, enabling the hole to be injected smoothly from the anode to the NPB and then to an emitting layer. The TE-OLED luminance reached 268cd/m2. There is a high energy barrier between the work function of Ag and MoO3 HOMO (5.3eV)about 1.1eVwhich is still not conducive to the hole injection, so a thin layer of high work function metal Au (work function 5.1eV) was added to the top of the anode silver, which more matches with the MoO3 energy level. It can make the hole easier to inject from the anode to MoO3 (HIL) and protect the silver from oxidation. At 8V, the luminance is increased to 413.7cd/m2, and the current efficiency is 0.81cd/A. The luminance is significantly improved. An electron transport/hole blocking layer TPBi (10nm) was added to enhance the electron transport capability and effectively block the holes with higher electron mobility and a higher HOMO energy level of TPBi. So that more holes can remain in the emitting layer and increase the chance of the electron-hole recombination to improve the luminance and current efficiency of TE-OLED. At 8V, the luminance and current efficiency can reach 611.4cd/m2 and 0.95cd/A, respectively.

2 September 2024 in Photonics
Verified
Journal Article
Open access
PDF file
FJFuh-Shyang Juang
Fuh-Shyang Juang
JCJia-You Chen
Jia-You Chen
WKWen Kai Kuo
Wen Kai Kuo
KPKrishn Das Patel
Krishn Das Patel
The study developed a large emission area of flexible blue organic light-emitting diodes (BOLED) on a polyethylene terephthalate/ Indium tin oxide (PET/ITO) substrate using a polycyclic skeleton ν-DABNA Thermally Activated Delayed Fluorescence (TADF) material. Initially, a 1 × 1 cm2 blue OLED was fabricated to optimize the layer thickness. The blue OLED structure consisted of PET/ITO/HATCN/TAPC/UBH-21:ν-DABNA/TPBi/LiF/Al. However, as the emission area increased to 3.5 × 3.5 cm2, the current density decreased due to the resistance of PET/ITO, leading to luminance non-uniformity. To address this issue, auxiliary Au lines were added to the ITO anode to enhance current injection. Despite this, when the Au lines reached a thickness of 30 nm, average light emission was disrupted. To improve the luminescence characteristics of large-area PET/ITO OLEDs, a capping and planarization layer of PEDOT:PSS was applied. Grid uniformity revealed a significant increase in overall luminance uniformity from 74.1% to 87.4% with the addition of auxiliary Au lines. Further increases in grid line density slightly reduced uniformity but enhanced brightness, resulting in brighter, flexible, large-area blue OLED lighting panels.

8 October 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
KPKrishn Das Patel
Krishn Das Patel
FJFuh-Shyang Juang
Fuh-Shyang Juang
DWDing-Yuan Wang
Ding-Yuan Wang
YLYi-Jing Lin
Yi-Jing Lin
YLYi-Sheng Li
Yi-Sheng Li
This research aims to develop top-emission OLEDs (Organic Light light-emitting diodes) that exhibit enhanced electro-optical properties regarding color purity, luminance, efficiency, stability, and longer lifetime. To achieve this aim, we have used silicon wafer substrates with a thickness of 675 m. Top-emission OLED fabrication on silicon wafer substrates requires careful material selection and layer configuration. This device structure is described as follows: Silicon/Al (100 nm)/ HATCN (10 nm)/ Dic-TRZ: Ir(mppy)3 (40 nm)/ TPBi (30 nm)/ LiF 1.2 nm / Al 19.9 nm. LiF/Al combination is used as the semi-transparent cathode. Research on top-emission OLEDs has demonstrated the importance of silicon wafer substrates in enhancing electro-optical properties. The optical properties of top-emission OLEDs are significantly influenced by factors such as the semitransparent cathode layer's thickness and the anode layer's surface roughness. Study findings encompass the impact of microcavity on TEOLEDs, dopant concentration on device performance, and device thermal conductivity and lifetime. To create a highly efficient top-emission OLED on a silicon substrate, we meticulously fine-tuned parameters such as the thickness of the cathode Al layer (19.9 nm), the organic layer thickness (HIL - HATCN 10 nm, HTL - NPB 30 nm, ETL - TPBi 30 nm, EML - DIC–TRZ: Ir(mppy)3 40 nm), and the dopant concentration. Electro-optical performance has been significantly improved through optimization, especially in devices with high dopant concentrations. The 38% dopant concentration experiments resulted in a peak current density of 201.97 mA/cm2, a luminance of 4776 cd/m2, and an efficiency of 2.36 cd/A at 9 V. In addition, the high dopant concentration has resulted in a narrow spectral range, indicating a strong microcavity effect. Additionally, Si-TEOLEDs were tested for lifetime under these specific conditions, exhibiting a half-life of 420 hours.